Monthly Archive: October 2018

CAT Caterpillar ET is genuinely a exceptional

2018A Cat ET software as Cat Caterpillar ET 2015A Software update version, 2018A Caterpillar Electronic Technician

softwarer With CAT ET 3 Cat caterpillar adapter 3 support caterpillar diagnostic till 2018.
1-1

As a outstanding obd2 options,CAT Caterpillar ET Diagnostic Adapter attributes a potent function.it not just can Show

“Logged Occasion Codes” to show engine greater than speeds,Greater temperatures, fuel consumption but additionally can

view ECM? current configuration and adjust user settings,carry out diagnostic tests and calibrations, and

calibrate.Electro-mechanical and electro-hydraulic elements .

Is definitely the Auto Scanner Tools Cat Comm III compatable applying the computer computer software CAT Caterpillar ET
2018A Is this an actual caterpillar portion or even a knock off? Thanks.Yes, this really is definitely the genuine CAT

adapter, It really is also the ONLY advisable adapter for CAT ET, but clearly other ones will carry out. It is going to

function fine for the version you could have, and 2018A is really the newest version.

What specifically is definitely the distinction in between a cat comm II & Cat Comm III. Is one just a usb connection

and one serial? Also, will this unit execute with my Cat 3126B marine units? Seriel no. 3GS01797 Thanks. CAT Comm II was

a serial port model, but since computers are no longer made with serial ports, they changed the design to a USB and

called it a CAT Comm III. So you are correct. This unit works with all CAT engines – Marine, on-highway, and off-

highway. On Marine units,  not sure where they put the plug, but it should be somewhere near the ECM (Typically). It

should be either a 6 pin or 9 pin connector.

Does this operate with CAT 3500 natural gas engines and 3600 natural gas engines? Thanks.If those Professional

Diagnostic Tools use CAT Electronic Technician (CAT ET) for the application, it is going to perform. Can the cat

communicate 3 also be used to read detroit and cummins engines if I have the correct software? Yes, it reads both J1708

and J1939 so it can read both of those. Keep in mind that this adapter only comes with the J1939 adapter end, so I would

recommend purchasing the J1708 adapter end from me as well if you plan on connecting to some older stuff.

Additional similar items can be found on www.cnautotool.com contact us.

How To Update SKP1000 Key Programmer Hardware ?

SKP1000 is a Multifunction programmer with 4’inch touch screen, mainly designed for auto Key programming. covers all functions of SuperOBD SKP-900 key programmer. SKP-1000 key programmer from CnAutotool.com is a convenient device which can perform immobilizer,  EPB+ Oil/service Reset , Mileage Adjustment and Ford and Nissan pin code calculation,and other special function, integrates more application and service, such as Maintenance Database, remote assistant, and One Key Update etc. supports almost all cars in the world, such as Audi,Volkswagen,Ford, Land Rover, Chrysler, Jeep, Toyota, Nissan, Honda, Mitsubishi, Hyundai, Kia, Mercedes, BMW (enable/disable key) and so on.

SKP-1000 Key Programmersupports Language:English

Here comes the step by step guide on how to update skp1000 key programmer.The skp1000 key programmer is the update version of  SKP900,it is more excellent than skp900.

Skp1000 hardware update procedures:

Take out the TF card and insert it into the card reader
plug into the computer USB port
go to My Computer/local disk (H:)
“Format” disk H:

17-1

Tip: Tick on the “Quick format” and click on“Start”
format completes
go to the official site to download the update file
then copy and paste the file into the TF card
plug the TF card into the machine
power on the machine to the main interface

click on “Firmware update”
17-2
choose “System firmware update”, press “Yes”
17-3
Firmware is updating,please wait.
17-4
Update successfully
17-5

Press “No” to back.

go to ” Adapter firmware update”
after finish, reboot the machine for use

Done.

How to solve the problem that BMW Icom A2 A3 host can’t be connected?

Aftre the BMW ICOM host is connected to the car via a 16PIN connector, and the other side is connected to the computer via a network cable. Your OBD2 Scanner BMW ICOM lan and system lights will light up. As follows:
10-1

But at this moment,the host can’t be found in the computer.As follows:
10-2

When meeting the problem,please update your BMW ICOM firmware as the following method:

1.Please connect BMW ICOM to the computer vith network cable and power on the BMW ICOM with a 12V power adapter.

2.Open the website address http://169.254.92.38:60080/by IE browser, username:root   password:NZY11502.

3.Click the “update firmware”,it will show ICOM firmware version information.

4.Choose the file ICOM-BootImage-01-11-01.bin,set image type to SYSTEM,click “Send the file”.

5.When shows “Write the image file to the flash?”,click “Yes”,then ICOM light turns red.

6.When shows “The SYSTEM IMAGE update was successfull”,click “Update Firmware”.

7.Choose the file ICOM-ApplicationImage-01-15-01.bin,set image type to APPLICATION.Click “Send the file”.It will takes a few minutes because of a little large file.

8.When shows “Write the image file to the flash?”,click “Yes”,then the ICOM light turns red for the second time.

9.It is all normal,click “reboot”.

After finishing these steps,please connect again,the ICOM host will be found in the computer,as follows:

10-3