Monthly Archive: December 2018

How to Slove MB SD C4 Cannot Access OBD2 Port

​When using china clone mb sd connect compact 4 Multiplexer, it could not link to the car computer, MB SD Connect C4 offered a message, saying like “check cable connection / turn ignition on”. Then tried again, clone SDconnect compact 4 multiplexer cannot access OBD2 port

According to customer’s feedback that he failed to access to the diagnostic OBD port when tried to use sd connect c4 read errors code from Benz SRS system. The system prompted an error message “check cable connection/turn ignition on”.
Possible Reason:

The error lies on the SD Connect C4’s battery.
​Solution from CnAutotool.com:

1) Check and record your MB SD Connect C4 multiplexer battery
2) Hook up a digital multimeter to set it to the direct current
3) Get two t-pins and plug them into the OBD socket at PIN 5 and PIN17 position
4) Put your positive lead to PIN16 and negative lead to PIN5.
5) Write down the voltage on the digital multimeter
6) Check if the voltage you from PIN16 and PIN 5 is same in step 1.
7) Find the light green wire with a blue tracer band of PIN10 of the OBDII connector.
8) If the voltage differs in step 1 and step 6, the problem is probably with your battery.
9) If the battery is damaged or broken, please replace your battery.

Lonsdor K518ISE Key programmer Test Results

 Lonsdor K518ISE Key programmer Test Results: after 90 days free trial update

Lonsdor K518ISE Key Programmer is tested by users 95.5% working fine after 90 days free trial update, it can work fine on an increasing number of car models. Here list some.

1. New 3 month trial period for certain special function.

I used it for Megane 3 with Smart Card system. The programmed key card in 2 minutes. No need pin code or anything…
Seems they have finally got a good competition for the Zedfull…..

2. Mégane 3 RS 2010, 4 buttons card, hands-free. Cards programmed 2 mins, Starts/stops, opens/closes, and the hands-free works too with factory cards

3. Fiat Doblo 2017. Program key ok And disabled key lost
Honda Accord 2012. Add key ok

4. Renault master3 2012 add key ok

5. BMW 1 F25 2012 fem add Key ok

6. Read pin add key Peugeot 208 2014 ok

7. Mazda cx9 2015 add key 4d-63 80bit ok

8. -Renault espace 2008 added 2 smart cards with no error, after finished the 2 cards were not recognized did not start car or work central locking

took long while, 5 minutes per card, MVP coded all cards in under 30 seconds, working perfectly…

9. – I made cas 2 one week ago no problem at all i made key in slot off lonsdor max 5 min

10. -Personally I never had issue with BMW cas 2/3 with lonsdor

11. – Volvo v50 2005 add key and remote ok

12. -Good news !! New update is good for MQB key !! Work fine add key on golf mk7 2015 ! Very fast and easy !!! Bravo !!

13. Mitsubishi space wagon 2003, precoded id61 and programmed key ok.

14. Corsa E (2016) read PIN (BCM) = OK

16. VW Amarok 2016 add key ok and backup EEPROM

17. FIAT 500 2008 Read Pin code and prepare remote key than program. ALL FINE

18. I have start loving this toy when i bought it was working 20% ok 80% not Now it is 95 – 5. Today megane 3 year 2009 keyless key made job in 2minutes

19. Porche Panamera 2010 km adjust obd job done

20. hyunday i20 2015 year
read pin ok
add key ok

21. Citroën c5 2008 read pin add key ok
307 Kline read pin fail/add key ok

22. 206 kline all key lost read pin ok about 3sec
23. Opel Zafira b read pin add key
24. Touran 2006 learn key and remote ok

25. Zafira B, read pin and add key, – Success (note, this failed under Zafira B in menu, but i chose type 3 from by system for both pin read and program and works fine)

26. Peugeot 607 2006 abrites won’t connect with BSI to read pin and key learning too.
Lonsdor read pin and program key 2 min.

27. Renault Fluence 2015 keyless go works excellent, in fact, zed full asks for pin and Lonsdor doesn’t. The key works ok in central module and keyless go,5 min job.

28. Suzuki Swift 2015-> (pcf7961)
all key lost
Program without pin – OK (2min)

29. Ford focus 2006 year
add key (all key lost) work all ok

30. Suzuki Swift 2013 all key lost – OK

31. Ford kuga smart spare key….ok, max 5min job

32. i30 2009 all key lost pin i key(7936) ok

33. grand Cherokee 2014 add smart ok

34. Lonsdor K518 Jeep Grand Cherokee 2015 Smart Key programming definetely. Read eeprom, calculate pin code OK.

35. Berlingo 2014 all key lost pin read ok

36. Fiesta 2013 keyless ok

37. Mazda 3 2014 add Smart key OK. All keys lost also OK.
I20 2014, read pin without working key and program key OK.

38. 2012 Ford Transit T350 2.2 RWD

AKL ok

Add Keys ok

39. Today Megane 3 year 2009 keyless key made job in 2 minutes.

Lonsdor K518ISE Key programmer FAQ:
Q: hmmm, i suppose i should update, seems like some new features are cropping up,
A: You need update and activate trial version for show new functions for 90 days. If you not activate trial version news functions not visible.

Q: What does trial for 90 data means?
A: for coverage in red color, after 90 days if you want still to use that coverage it will be paid option

Information about subscription update for a year: 600$

I’m planning to buy, but now this will be ban.

Q: Bmw X5 cas3+ the year 2008 add key not successful read ok all , but was not able to add key , ZedFull add in 1 min .
A: you must add it with key in ignition, in slot doesn’t work ok, but with key in ignition should work. tested by me

Scania VCI-3 VCI3 Scanner Wifi Wireless Diagnostic Tool Online

V2.21 Scania VCI-3 VCI3 Scanner Wifi Wireless Diagnostic Tool Online

SCANIA VCI3 Highlights:

1. Scania VCI3 is designed to support all Scania diagnostic systems based on CAN network, it’s a extremely fast yet very compact diagnostic tool.
2. One of the most interesting new features that can be found in Scania VCI3 is a Wifi wireless connection (also there is a USB connector for wired connection).
3. From now you can work without wired connection to your truck, just forget these problems like damaged data cables and other disadvantages of wired connections.
4. Software support for Scania VCI3 appeared in Scania SDP3 2.18 version so if you want to use this tool you need this version of SDP3 or later versions of this software.
5. The device is designed for full service trucks, buses and other heavy vehicles, which produces the corporation SCANIA. Adapter works in conjunction with software SDP-3.
6. The adapter does not work with trucks and engines manufactured before 2004.
7. The main feature of VCI-3 – Work through a high-speed WI-FI connection. Also in the device has a USB port.

Attention: You need to install the V2.21 Scania VCI-3 Software on window7 32bit.

Scania VCI-3 Scanner Display:

1-5