Monthly Archive: April 2019

Porsche Piwis Tester III with Panasonic CF54 Piwis3 PT3G Ver 37.250.020

Porsche Piwis Tester III with Panasonic CF54 Piwis3 PT3G Ver 37.250.020

Porsche Piwis Tester III is the newest fully operational diagnostic equipment based on PIWIS vehicle interface and Porsche software. Piwis Tester III provides exclusive support for Panamera G2, Cayenne E3 and all 2017 model range and above also provides legacy support for older models.

It is the new third generation Porsche diagnostic tool, it’s update to modern user interface, more faster performance, also have: license automatic update, online view of the technical documents, fault finding guide, online programming, faster and more efficient work.
Porsche Piwis Tester III Main Unit


Version: 37.250.020
License: Unlimited
Update: Via DVD or Online
Support Online Programming, no develop mode
Porsche Piwis 3 Languages


Porsche Piwis Tester III main functions
? General ECU diagnostics (DTC read/clear)
? Guided fault finding
? ECU programming/coding
? Real-time control parameters display
? Electrical schematics mapping

Porsche PIWIS 3 advantages
? Exclusive support for 2017 model range and above (Panamera G2, Cayenne E3)
? Fast and stable connection Simulation mode (diagnostic session without VCI connection)
? End user capable DVD update
? Wired USB connection

Porsche PIWIS 3 Packing List:
1pc x Piwis 3 VCI
1pc x USB Cable
1pc x Laptop Power Adapter
1pc x Panasonic CF54 Laptop(Software Preinstalled,Ready to work)

Porsche-Piwis-Tester-III-with-Panasonic-CF54-Piwis3-PT3G-Ver-37.250.020-3 Porsche-Piwis-Tester-III-with-Panasonic-CF54-Piwis3-PT3G-Ver-37.250.020-4 Porsche-Piwis-Tester-III-with-Panasonic-CF54-Piwis3-PT3G-Ver-37.250.020-5

How to Solve K518 program Renault primastar 2004 key ok but not start van

Lonsdor K518ISE:Renault primastar 2004 – program key all went OK, but after finished the key would not start van, or work with central locking.

2x keys tested, both from AUTOWAVE company. keys were LOCKED after programming.

Programmed under Renault trafic first, then Renault master second key used.

Maybe it was faulty keys, I don’t know, autowave keys are usually good.


ISK (Crypto low, Crypto high) = is the 6 byte in HITAG2 which close the pcf (like a password) if you have cloning stuff you can see the ISK after key decoding, like Handy or something or some tools are informing you like Renault ECu tool. Whatever, you got the ISK
Take your transponder programmer and enter the isk. Put the locked key to the programmer, it depends the prommer there is a different ways but you can always unlock Renault hitag2 keys or cards(7946, 7947) if you have the ISK.
And yes even the EFFI able to do it, my miraclone have a dedicated button..etc.
When I programming Renault I always writing down the ISK. If the key is broken/defected/something I can start over after unlock.

In addition, the only key you can’t unlock if you know ISK is the new Renault card for Meganne. 2. If order by official dealer card come locked with Vin you order and can’t unlock with any way.

Lonsdor K518ise key programmer add non-smart keys to Renault Clio 3

Confirmed! Lonsdor K518ISE Key Programmer is able to add non-smart keys to Renault Clio 3

In Lonsdor K518ise:

Immobilizer – Renault – select from vehicle – Clio – Clio 3


Add non-smart keys


Downloading application…


Lonsdor starts programming new keys…

Turn off the ignition switch and remove the key


Current key: 2

lonsdor-k518ise-renault-clio-5 lonsdor-k518ise-renault-clio-6
Insert the key and switch ignition on


Switch ignition off, remove the key


Insert the key and switch ignition on


Switch ignition off, remove the key


Continue to program the next key


Key learn complete


Test both keys

lonsdor-k518ise-renault-clio-13 lonsdor-k518ise-renault-clio-14

How to solve ISTA-P error 94201 63031 63014

10 steps to solve ISTA-P error 94201 63031 /63014 after boot.
1.End the dialogue.
2.Disconnect ICOM device from the BMW.
3.unplug the car battery for 10 minutes.
4.Plug the car battery again, boot the new ISTA/P dialogue.
5.Turn on the ignition.
6.Connect the ICOM device to the BMW ICOM.
7.Choose “ICOM” in the ISTA/P connection manager.
8.Boot the programming dialogue.
If the problem is not solved, please do by following below steps.
1.End the dialogue.
2.To confirm the repair shop has no the activated ISTA/P dialogue.
3.Reboot the programming device (PC, ISID or ISSS)
4.Use other ICOM BMW to restart new programming dialogue. Connect ICOM to the vehicle with the ignition is on.
If the problem is not solved, please firstly follow the
[=>00044444EN] description to collect Log file, then contact the tech support.
Thanks to Susan who are working at,one user bought from her one ISTA-D 4.04.12 ISTA-P and come across the above error, with her help, the problem is solved finally.

How can I get cat et license key and get cat et software downlaod via Internet

As we all know the cat et last version is 20014C v1.0,but the hardware only can use CAT ET Software,the question is the license is outdate,how can I get the last key?
Now I share the pic of getting the license key,
The fist is we need the software of cat et 2009Bv1.0,if you doesn’t have it, you can get it from me, I have the software 2009-2014c,all of them.


Next and then you will see:


And we accept the terms in the license agreement


It is working, installing, When the software installation is complete, we will find the software icon on the desktop.


Open it,


Click ok tag, We see the Tips that the software without authorization.
Copy the license code,and sent it to me we can help you for license key.


When paste the license key and authorize ,the cat et tell us it is licensed.

in fact,the steps of cat et 2010-2011B is the same as 2009B

2018 Launch X431 PROS Mini review 4.5 stars

2018 Launch X431 Pro Mini is an amazing little tool and perfect for auto body shops who are pre and post scanning vehicles. This will perform/test/reset TPMS functions, occupancy sensors, SAS calibrations etc etc….. What’s most surprising is X431 PROS Mini won’t break the bank. There are cons but at this price and this time I’m willing to overlook them given the functionality. The seller’s willingness to correct these functions may change my rating down the road. IN fact I was going to wait to rate but I like the tool well enough so far I wanted to tout a little. (4 star tout anyway) ??

X431 PROS Mini PROS:
“no such thing as 100% complete” but very “complete” coverage of software. (admittedly I’ve been using this for about 2 or 3 weeks but so far so good
hand strap is just fantastic and provides a very secure grip on the scanner without fatique
blue tooth dongle is reliable and fits well
not sure if I’ll ever use the extra connectors but I have them if needed
Android pad is “fast enough” and the touch screen response perfectly
WIFI is reliable and decent range.
Scan reports are very easy to read and if you print them in color they show red faults and green clear code areas. VERY NICE!

X431 PROS Mini CONS:
Personally speaking, Android operating system is 5.1 but I’m hoping for the purpose of this tool security will work. (LEOGLOBAL UPDATE THIS PLEASE)
LEOGLOBAL needs to seriously update the user functions to allow for customizing the quick start buttons and removing that awful screen capture button on the home keys, among other things.
NO SD CARD SLOT!!! This is 2018, but if it were 2014 when 5.1 Lollipop came out I’d expect to have an SD card slot for extra storage. This 16 GB isn’t going to last that long!
BATTERY life is decent while the tool is in use but even if you shut down the app and blank the screen something is still draining the battery way too fast. You must power down or keep it on the charger to ensure your battery stays charged.

WAY WAY WAY too many button pushes to back out after a scan is complete. There is a back arrow in the software but there needs to be a simple “exit diagnostics” after you are done without having to click multiple times to get to the warning beep that reminds you to grab the dongle.

LEOGLOBAL & LAUNCH PLEASE PLEASE change the software to allow the user to print to ANY Bluetooth or WIFI printer, not just the LAUNCH thermal printer. I like color reports.

LEOGLOBAL & LAUNCH PLEASE PLEASE change the software to allow the user to designate where the reports are stored AND allow the file name to be changed/edited at the time of the save. The file names are too long and you have to go through each one to find the scan you wish to share/print/email/whatever. I shouldn’t have to open a report to find out if it’s the one I need. (EDIT: SINCE YOU INPUT THE CUSTOMER NAME AND MAKE THAT SHOULD BE INCLUDED IN THE FILE NAME FOR EASY IDENTIFICATION AND THE DATA IS ALREADY INPUT) You can’t sort by date either, which would help some at least. In order to print to my network printer I have to save it within the Launch software then “share” it to the external app provided with the tablet, where “share” equals save it to a folder of your choosing. The problem is you still can’t rename the file first. The extra steps required to save files and print to a regular printer are annoying and shows sloppy coding.

TOO MANY MAKES I’ll never work on. I wish you could delete the software for the models you will never work on.

Even with the annoyances you’ll get into a groove but whoever is responsible for the coding hopefully will make this more user friendly. Catch this on a lightning deal like I did and in spite of the cons you’ll be glad you bought it.

How to Write Tyre Pressure ID to Kia K5 2012 with Launch X431 V

Actual Measurement: Dongfeng KIA 2012,VIN= LJDKAA241C0*****,dashboard as


Device: Launch X431 V 8inch Tablet

1. Tire pressure sensor ID consists of 8 letters and numbers, as shown in Figure 2. After the new
sensor is bought back, take a picture and record the ID.


2. In the process of writing the sensor ID, pay particular attention to the one-to-one correspondence
of the tire pressure sensors, left front, left rear, front right, right rear, and four sensor IDs to ensure
that each corresponding write.
3. Before and after the replacement of the tire pressure sensor, the old sensor and the ID of the new
tire pressure sensor replacing its position should be recorded, as well as the tire position;
4. After some models of sensors are written, the tires need to run for a period of time, or the sensor
activation tool is required to activate the sensors, and then the tire pressure sensors can work

Operation Procedure:
1. Select Dongfeng Yueda V21.20 above;
2. Select 16PIN diagnostic socket;
3.Manually select menu;
4. Select K5(TFC);
5. Select 2015;
6. Select G2.0NuMPI
7. Select TPMS;
8. Select special function item,Shows a list of special features under TPMS (Tire Pressure Monitoring System), as shown in Figure 3;


9. Select the wheel sensor ID write, as shown in Figure 4 information;


10. Click OK to read the currently set sensor ID. The keys C1, C2, C3, and C4 correspond to the
input sensor 1, the sensor 2, the sensor 3, and the sensor 4. In the writing process, pay attention to
one-to-one corresponding sensor ID, can not go wrong, as shown in Figure 5;


11. Click C1, enter the sensor 1, change the ID of the sensor 1, as shown in Figure 6


12. Click C2, enter the sensor 2, change the ID of the sensor 2, the same operation to change the ID
of the sensor 3, the sensor 4, after the completion of the four ID modifications, as shown in Figure 7;


13. Click to confirm and save, four tire pressure sensor ID prompt write success, as shown in Figure


14. Click to confirm, this time will read again the four tire pressure sensor ID, this time is the value
of the sensor ID after writing, as shown in Figure 9;


15. Exit the software and check that the instrument fault light is off. The test run was normal.
Note: Some models may need to run the sensor ID for about 10 minutes after the sensor ID is
written or need sensor activation tool to activate the sensor.

Launch X431 Pro Mini is the mini version of X431 Pro

What is Launch X431 Pro Mini and what is Launch X431 Pro? Any difference?

Look at the chart here. This is tech support from


Special functions incl.
Oil Reset Service
Steering Angle Calibration
Electronic Parking Brake Reset
Battery Register / Battery Maintenance
ABS Bleeding
Electronic Throttle Position Reset / Learn
Diesel Particulate Filter (DPF) Regeneration
Tire Pressure Monitor System Reset
Gear Learning
Immobilizer Matching
Fuel Injector Coding

Launch X431 Car List:
Acura, Changan, Daweoo, Gaz, Hafei, Huachen, Jiao, Lexus, Xiali, Xinkai, Benz, Fiat, Holden, Maruti, Opel, Peugeot, Saab, Ssangyong, Tata, Changhe, Flyer, GMSA, Infiniti, Mahindra, Perodua, Proton, Qirui, Tlisuzu, Zhongshun, EOBD2, Euroford, GM, Jaguar, Renault, Smart, Sprinter, USAFord, VAZ, VW, Changcheng, Dacia, Ford, HaoQing, Jinlong, Liuwei, Rover, ZhongTai, ZhongXing, Bxfiat, HM, Isuzu, Jacty, JPIsuzu, Mazda, Seat, Skoda, Suzuki, BMW, Daihatsu, Mitsubishi, Porsche, Toyota, Volvo, Audi, Chrysler, Citroen, Hyundai, Kia, Lancia, Landrover, Nissan, Romeo and Subaru.

In summary, Launch X431 PRO3 win in hardware (helps better smoothness of diagnostics/programming, running speed, visual enjoyment). It share the same functions and features as Launch X431 PRO tho.

(Solved) John Deere Service Advisor Search Engine Error

This is for anyone when he/she runs the John Deere Service Advisor heavy duty diagnostic software, the system appears error message that the search engine module can not be loaded and then the program ends.


Optional solutions:

Solution 1:

Run as system administrator, roll back pc date reactivate using activator Then roll date back to normal date if error still renew once again. Been working for me so far.

Note that, don’t know how long it stay working but works im sure someone will have solution for it soon.

Also advice if doing fresh install roll back the date on pc do the install after then install and activations have been done.
Go to task manager look for the service adviser on have it start its tasks in 2030 :save and then reset your pc date should be good for while

Solution 2:

if you set a date before the lightweightidol license expired, start the lightweightidol service, set the real date and start Advisor, it works.

Solution 3:

start advisor. when error comes with “search engine” Close John Deere SA. afterwards set your PC date to feburary 2015. start SA again (run as administrator). it now comes with error on licence. close SA Again. set pc date back to normal. run SA Again. now it Works.

Solution 4:

The search engine error can be solved.
Set back the date, before the expiry date found in Service ADVISOR\SUIR\license.log (august 14 in my case). Start LightweightIDOL service. Set the real date, and Advisor working again.
I made a batch file to simplify it. To make it work Control Panel/Regional/short date format have to be yyyy-mm-dd or you have to modify batch. Maybe you have to modify ServiceADVISOR.exe path too in the batch. Have to run as administrator.


Solution 5:

I have had the same error with ssearch engine connection in JD SA.
reinstalled it twice, changed system date back and forward, run activator. No result for me.

But actually I found the solution for this issue.
Just need to install july update from the post…#pid758969
And the error disappeared.

newer data discs (2016/02)

Solution 6:

back date to 08.10.16
install JD SA, restart, activate, mount latest disk you have (05.2016) and install update, for finish get license error, ignore and close, set actualy date, run JD SA -> works fine, install july update

testing today on 3 laptops (Windows 7 and 10)

On a side note: procedure about turning off the updates

don’t know how long it stay working but works im sure someone will have solution for it soon.

Also advice if doing fresh install roll back the date on pc do the install after then install and activations have been done.
goto task manager look for the service adviser on have it start its tasks in 2030 :save and then reset your pc date should be good for while Smile (SO TURN IT OFF IN TASKMANAGER SO IT STARTS 20 30 YEARS FROM NOW!!)

Fresh new installations also work but can be much more complicated sure a patch would be much easier. But it can be done with out a patch so far

In taskmanager I don’t stop any service just put service advisor updater to 2030 to start

also makes sure eculp.ini configurator reads like this

A valid ECULP License has been found

Licenses for the following modes have been found:
TestCell Programming
FinalEOL Programming
Service Programming
ECUCPP Programming Tool

All JD Components were found and properly licensed

JDEcu : Version 1.0 : 01-apr-2021
JDConfig : Version 1.0 : 01-apr-2021
JDData : Version 1.0 : 01-apr-2021
JDIntelHex : Version 1.0 : 01-apr-2021
JDPayloadReader : Version 1.0 : 01-apr-2021
JDPayloadProcessor : Version 1.0 : 01-apr-2021
ECULoaderProgram : Version 1.0 : 01-apr-2021
ECULP_TestCell : Version 1.0 : 01-apr-2021
ECULP_FinalEOL : Version 1.0 : 01-apr-2021
ECULP_Service : Version 1.0 : 01-apr-2021
ECULP_TestCell_OEM : Version 1.0 : 01-apr-2021
ECULP_FinalEOL_OEM : Version 1.0 : 01-apr-2021
ECULP_Service_OEM : Version 1.0 : 01-apr-2021
ECULP_ECUCPP : Version 1.0 : 01-apr-2021
ECULP_Direct_EOL_Output : Version 1.0 : 01-apr-2021
ECULP_OEM_DISTRIBUTOR : Version 1.0 : 01-apr-2021
Service_ADVISOR_Ag : Version 1.0 : 01-apr-2021
Service_ADVISOR_CF : Version 1.0 : 01-apr-2021

The last – if all tips/solutions above don’t work for you,

John Deere Service Advisor 4.0 Crack – No Search Engine Error