Launch X431 Tools | obd2scantool.info

Europe Ford Focus Mileage Programming after Replacement by Launch X431

This article show a guide on how to use Launch X431 to program mileage for Europe Ford Focus after instrument cluster replacement. This function is only necessary on newly installed instrument clusters.

The attention of the two points :
A,It is not possible to overwrite a value lower than the mileage.
B,If the odometer write failed, you can try again.

Procedures:
Diagnose：Select “Calling system” menu.

Wait for 1 minutes. Then the Vehicles Specification screen displays.

Select “ICM” menu

Enter Odometer Write functions in the “SPECIAL FUNCTION” menu

When selecting “Odometer Write”, it will display as below show.

It can only enter a value higher than actual mileage.(Now Mileage:34531Miles)

If you enter a value lower than actual mileage,it show as below

Press ok to reenter

when you enter a correct data, it will show as below

Press ok to Complete.

Done!

wp-admin August 26, 2019 Launch X431 ToolsLaunch, Launch X431, Launch X431 diagnostic tool, Launch X431 for sale, Launch X431 scan tool, Original Launch X431, X431 0 Read more >

How to use X431 V+ with HD-III module for heavy duty truck diagnosis?

Launch HD-III module is compatible with X431 V+, pad3, pro3 etc, only available for X-431 V+ of heavy duty trucks. With HD-III module, it can read the vehicle data and then send it to the X-431 V+ via wireless BT/WLAN communication. It will replace HD II module.

First is HD-III module outlook: in Blue color, with LED indicators etc.

As the 3rd generation of heavy-duty module, it works as a vehicle communication interface device, which is used to read the vehicle data and then send it to the X-431 V+ via wireless BT/WLAN communication. The LED indicators enable you to easily identify the working status of the module.

1 DC-IN power jack: For connecting the power adaptor.

2 Diagnostic socket: For connecting the diagnostic cable.

LED indicators: It is defined as follows:

? Vehicle: While communicating with the vehicle, the indicator lights up and flashes. Otherwise, it will not illuminate.

? Power: It illuminates solid red when the module is powered on.

? BT: Blue indicates the module is working in wireless BT mode.

? I/O: It lights up when the module is connected to the diagnostic tool via data cable (Currently disabled and only reserved for subsequent function extension).

* Wireless: It lights up when the module works as a wireless hotspot or network adaptor.

Data I/O port: Currently disabled and only reserved for subsequent function extension.

Second is HD-III module features in BT/WLAN communication.

HD-III module: send the vehicle data to the diagnostic tool via wireless Bluetooth or Wlan

WIFI module:

HLK-RM08K

* Frequency range: 2412-2472MHz

* Transmit power: 19.29dBm

Wireless BT module:

YG-218M-A2

? Frequency range: 2402-2480MHz

* Transmit power: 16.62dBm

Launch X-431 V+ is compatible with HD-III module VCI module. Besides the BT communication, the HD-III VCI module comes loaded with a built-in WLAN module, which can work as a wireless hotspot or a network adaptor.

Below shows how the X-431 V+ system works.

Third is on how to connect HD-III module to the vehicle?

*Notes:

a). For commercial vehicles, refer to the above connection method to proceed.

b). For passenger vehicles, replace the “Non-16pin connector” with “OBD I adaptor” +

“non-16pin connector (for passenger vehicles)”. Other connections shall also apply.

Finally, diagnose with X431 V+.

It is required to register as member, activate the connector, download the software etc.

It is claimed to be able to update online for one year. Any confusion that you may have, there is a sheet of quick guide to follow.

X431 HD III Quick Start Guide

X431 V+ user manual

X-431 HD III heavy truck module overseas online configuration Software List

wp-admin August 7, 2019 Launch X431 ToolsHD module, Launch HD-III module, Launch X-431 V+ HD III, Launch X-431 V+ HD3, Launch X-431 V+ HDIII, Launch X431 HD3, Launch X431 HDIII Module, X-431 V+ 0 Read more >

Launch X431 Configure & Initialize Ford PATS Passive Anti Theft System

Some FORD models(Europe) with timed coding are equipped with Passive Anti Theft System(short for PATS).

And for more Launch X431 Test Case,check here:How to use Launch X431

PATS diagnosis consists of the following three options:

1.Ignition Key Erase

2.Ignition Key Programming 3.Module Initialization

1)If new keys are added, it is enough to perform “Ignition Key Programming”function.

2)If engine ECU or Immo. ECU replaced, all above options must all be performed.

1.Diagnose：Select“Calling system”menu(See Figure 1),and wait for 1-2 minutes.

Then the Vehicles Specification screen displays (See Figure 2).

2.Select“PCM”menu(See Figure 3)and “Passive anti theft system functions” in the “SPECIAL FUNCTION” menu(See Figure 4）.

3.When selecting “Passive anti theft system functions”, it will display as Figure5,then perform as the following order: first, Ignition Key Erase，second, Ignition Key Programming，last, Module Initialization.

1.Ignition Key Erase

Select“Ignition Key Erase”menu with the hints displayed（See Figure6）：This procedure will erase all stored keys from the PATS system memory. Once completed you will need to use the Ignition Key Programming option to program a minimum of 2 new keys before the PATS system will operate correctly.

Touch “OK”, then appears hint information as Figure 7：You will be required to connect the diagnostic tester to the vehicle for[12] minutes before security access is allowed.

Touch “OK” button，information display as Figure8：Gaining security access: 11 Min 56 Sec

During 12 minutes, hint information appears as Figure9：The following procedure will erase all known keys. It is important to have two keys available to program after this procedure as the vehicle will not start before two keys have been learned,Are two PATS keys available?

Select “ON” button to quit“Ignition Key Erase” function.

Select “YES” , the following messages appears: Set ignition switch to ON(Position II).

Select “OK” button,then “Ignition Key Erase” function is completed.

2.Ignition Key Programming

Select “Ignition Key Programming” menu，hint information appears as Figure10：

This procedure will add keys to the PATS system memory. Keys already known to the PATS system will not be erased. This system requires keys with a BLUE colored transponder insert. Keys with engraving on the transponder insert are NOT suitable.

When programming a remote control key fob ensure that the correct part for the vehicle is used. Different types may look identical but are not interchangeable.

When select “OK” button，hint message appears as Figure11：Security Access may be lost if the following actions are not completed in 10 seconds, The time starts as the ignition is switched off, Set ignition switch to OFF[Position 0],Insert a new key into the ignition, Set the ignition switch to ON, Press OK when finished.

Select “OK”, displaying: Set ignition switch to OFF(Position I).

Select again “OK”, displaying: Set ignition switch to ON(Position II).

Select again “OK”, then “Ignition Key Programming” function is completed.

3.Module Initialization

Select “Module Initialization”menu,and the submenu displays as Figure 12：

Select “PCM” menu， and appears hints as Figure 13：This option is used to match the PCM to the HEC or FIP as appropriate. It is important that the key in the ignition is programmed to this vehicle before using this option. If the key is not programmed, then module initialization will not be possible. If initialization fails,clear and reprogram all the PATS keys for this vehicle and rerun the moduleinitialization option again.

Select “OK” button, appears hint as Figure 14：Module reset is now complete

Select “OK”, then displays hints: Set ignition switch to OFF(Position I).

Select “OK”, then displays hints：Set ignition switch to ON(Position II).

Select “OK”, then displays hints：Set ignition switch to OFF(Position I).

Select “OK”, then displays hints：Set ignition switch to ON(Position II).

Select “OK”, then displays hints as Figure 15：PATS Module initialization is now complete.

Select “OK”, then the PCM initialization is completed.If there is not special function menu displayed when select following as Figure3,and the vehicle is indeed a PATS with timed coding mode,please send all information displayed in Figure 2 to us.

When you select “Calling system” in Figure 1 and wait for 1-2 minutes,if information as Figure 16 displayed, please send it to us.

From Auto Repair Technician Home, po

wp-admin May 1, 2019 Launch X431 ToolsLaunch, Launch X431, Launch X431 diagnostic tool, Launch X431 for sale, Launch X431 scan tool, Original Launch X431, X431 0 Read more >

2018 Launch X431 PROS Mini review 4.5 stars

2018 Launch X431 Pro Mini is an amazing little tool and perfect for auto body shops who are pre and post scanning vehicles. This will perform/test/reset TPMS functions, occupancy sensors, SAS calibrations etc etc….. What’s most surprising is X431 PROS Mini won’t break the bank. There are cons but at this price and this time I’m willing to overlook them given the functionality. The seller’s willingness to correct these functions may change my rating down the road. IN fact I was going to wait to rate but I like the tool well enough so far I wanted to tout a little. (4 star tout anyway) ??

X431 PROS Mini PROS:
“no such thing as 100% complete” but very “complete” coverage of software. (admittedly I’ve been using this for about 2 or 3 weeks but so far so good
hand strap is just fantastic and provides a very secure grip on the scanner without fatique
blue tooth dongle is reliable and fits well
not sure if I’ll ever use the extra connectors but I have them if needed
Android pad is “fast enough” and the touch screen response perfectly
WIFI is reliable and decent range.
Scan reports are very easy to read and if you print them in color they show red faults and green clear code areas. VERY NICE!

IT AIN”T ALL GOOD:
X431 PROS Mini CONS:
Personally speaking, Android operating system is 5.1 but I’m hoping for the purpose of this tool security will work. (LEOGLOBAL UPDATE THIS PLEASE)
LEOGLOBAL needs to seriously update the user functions to allow for customizing the quick start buttons and removing that awful screen capture button on the home keys, among other things.
NO SD CARD SLOT!!! This is 2018, but if it were 2014 when 5.1 Lollipop came out I’d expect to have an SD card slot for extra storage. This 16 GB isn’t going to last that long!
BATTERY life is decent while the tool is in use but even if you shut down the app and blank the screen something is still draining the battery way too fast. You must power down or keep it on the charger to ensure your battery stays charged.

WAY WAY WAY too many button pushes to back out after a scan is complete. There is a back arrow in the software but there needs to be a simple “exit diagnostics” after you are done without having to click multiple times to get to the warning beep that reminds you to grab the dongle.

LEOGLOBAL & LAUNCH PLEASE PLEASE change the software to allow the user to print to ANY Bluetooth or WIFI printer, not just the LAUNCH thermal printer. I like color reports.

LEOGLOBAL & LAUNCH PLEASE PLEASE change the software to allow the user to designate where the reports are stored AND allow the file name to be changed/edited at the time of the save. The file names are too long and you have to go through each one to find the scan you wish to share/print/email/whatever. I shouldn’t have to open a report to find out if it’s the one I need. (EDIT: SINCE YOU INPUT THE CUSTOMER NAME AND MAKE THAT SHOULD BE INCLUDED IN THE FILE NAME FOR EASY IDENTIFICATION AND THE DATA IS ALREADY INPUT) You can’t sort by date either, which would help some at least. In order to print to my network printer I have to save it within the Launch software then “share” it to the external app provided with the tablet, where “share” equals save it to a folder of your choosing. The problem is you still can’t rename the file first. The extra steps required to save files and print to a regular printer are annoying and shows sloppy coding.

TOO MANY MAKES I’ll never work on. I wish you could delete the software for the models you will never work on.

Even with the annoyances you’ll get into a groove but whoever is responsible for the coding hopefully will make this more user friendly. Catch this on a lightning deal like I did and in spite of the cons you’ll be glad you bought it.

wp-admin April 4, 2019 Launch X431 ToolsLaunch X431 Pro Mini, Launch X431 Pro Mini Bluetooth, Launch X431 Pro Mini OBD2 Diagnostic Scan Tool, Launch X431 PRO MINI WIFI Bluetooth, X431 Pro Mini 0 Read more >

How to Write Tyre Pressure ID to Kia K5 2012 with Launch X431 V

Actual Measurement: Dongfeng KIA 2012，VIN= LJDKAA241C0*****，dashboard as
follow:

Device: Launch X431 V 8inch Tablet

NOTE:
1. Tire pressure sensor ID consists of 8 letters and numbers, as shown in Figure 2. After the new
sensor is bought back, take a picture and record the ID.

2. In the process of writing the sensor ID, pay particular attention to the one-to-one correspondence
of the tire pressure sensors, left front, left rear, front right, right rear, and four sensor IDs to ensure
that each corresponding write.
3. Before and after the replacement of the tire pressure sensor, the old sensor and the ID of the new
tire pressure sensor replacing its position should be recorded, as well as the tire position;
4. After some models of sensors are written, the tires need to run for a period of time, or the sensor
activation tool is required to activate the sensors, and then the tire pressure sensors can work
normally.

Operation Procedure:
1. Select Dongfeng Yueda V21.20 above；
2. Select 16PIN diagnostic socket；
3.Manually select menu；
4. Select K5（TFC）；
5. Select 2015；
6. Select G2.0NuMPI
7. Select TPMS；
8. Select special function item，Shows a list of special features under TPMS (Tire Pressure Monitoring System), as shown in Figure 3;

9. Select the wheel sensor ID write, as shown in Figure 4 information;

10. Click OK to read the currently set sensor ID. The keys C1, C2, C3, and C4 correspond to the
input sensor 1, the sensor 2, the sensor 3, and the sensor 4. In the writing process, pay attention to
one-to-one corresponding sensor ID, can not go wrong, as shown in Figure 5;

11. Click C1, enter the sensor 1, change the ID of the sensor 1, as shown in Figure 6

12. Click C2, enter the sensor 2, change the ID of the sensor 2, the same operation to change the ID
of the sensor 3, the sensor 4, after the completion of the four ID modifications, as shown in Figure 7;

13. Click to confirm and save, four tire pressure sensor ID prompt write success, as shown in Figure
8;

14. Click to confirm, this time will read again the four tire pressure sensor ID, this time is the value
of the sensor ID after writing, as shown in Figure 9;

15. Exit the software and check that the instrument fault light is off. The test run was normal.
Note: Some models may need to run the sensor ID for about 10 minutes after the sensor ID is
written or need sensor activation tool to activate the sensor.

wp-admin April 3, 2019 Launch X431 ToolsLaunch X-431 V+, Launch X431 V 8 inch, Launch X431 V 8inch Tablet, Launch X431 V 8″, Launch X431 V Bluetooth, Launch X431 V Bluetooth Wifi, Launch X431 V Wifi, Launch X431 V+, Launch X431 X-431 V, X-431 V+, X431 pro, X431 V 8inch, X431 V+ 0 Read more >

Launch X431 Pro Mini is the mini version of X431 Pro

What is Launch X431 Pro Mini and what is Launch X431 Pro? Any difference?

Look at the chart here. This is tech support from www.cnautotool.com

Special functions incl.
Oil Reset Service
Steering Angle Calibration
Electronic Parking Brake Reset
Battery Register / Battery Maintenance
ABS Bleeding
Electronic Throttle Position Reset / Learn
Diesel Particulate Filter (DPF) Regeneration
Tire Pressure Monitor System Reset
Gear Learning
Immobilizer Matching
Fuel Injector Coding

Launch X431 Car List:
Acura, Changan, Daweoo, Gaz, Hafei, Huachen, Jiao, Lexus, Xiali, Xinkai, Benz, Fiat, Holden, Maruti, Opel, Peugeot, Saab, Ssangyong, Tata, Changhe, Flyer, GMSA, Infiniti, Mahindra, Perodua, Proton, Qirui, Tlisuzu, Zhongshun, EOBD2, Euroford, GM, Jaguar, Renault, Smart, Sprinter, USAFord, VAZ, VW, Changcheng, Dacia, Ford, HaoQing, Jinlong, Liuwei, Rover, ZhongTai, ZhongXing, Bxfiat, HM, Isuzu, Jacty, JPIsuzu, Mazda, Seat, Skoda, Suzuki, BMW, Daihatsu, Mitsubishi, Porsche, Toyota, Volvo, Audi, Chrysler, Citroen, Hyundai, Kia, Lancia, Landrover, Nissan, Romeo and Subaru.

In summary, Launch X431 PRO3 win in hardware (helps better smoothness of diagnostics/programming, running speed, visual enjoyment). It share the same functions and features as Launch X431 PRO tho.

wp-admin April 2, 2019 Launch X431 ToolsLaunch X-431 PRO3, Launch X-431 V+, Launch X431 Pro Mini, Launch X431 Pro Mini Bluetooth, Launch X431 Pro Mini OBD2 Diagnostic Scan Tool, Launch X431 PRO MINI WIFI Bluetooth, Launch X431 V+, Launch X431 X-431 V+(X431 Pro3), X-431 V+, X431 Pro Mini, X431 V+ 0 Read more >

How to use Launch X431 Pro Mini on Toyota VITZ scan & special functions

Here comes easy step-by-stey guide on how to use Launch X431 Pro Mini to diagnose & perform special functions on Toyota VITZ.

Vehicle Information:

Toyota VITZ

Model: KSP90

Engine Type: IKRFE (Gasoline)

Year:2005

Cylinder number: 3

Toyota VITZ diagnostic tool to use:

Launch X431 Pro Mini(it’s a professional diagnostic maintenance tool for workshop.

Procedure:

Choose Area “Asia”, then “Toyota”

Come to Toyota version V48.91, click “Submit”

Choose among 16pin DLC (Japan), 17Pin Toyota – 17DLC,17PiN Toyota – 17F or 22PIN DLC.

For example, choose “16pin DLC (Japan)”, then come to “Automatically search” and “Manually search”

Choose between Belta and VITZ.

Choose year “08/2008 -11/2010

X431 pro mini read out vehicle information

Choose “System Scan”.

You can see x431 pro mini can access to all systems very fast

Select Engine and ECT, then you can see all of X431 Pro mini functions incl.

Read fault code, clear fault memory, read data stream, actuation test, read freeze frame,oil reset

special functions.

Choose “Read DTC” then clear them.

Back and check X431 Pro mini special function on Toyota.

Two options: “Auto search special function” and “All special function”

Choose “All special function” and I got many special functions (see below picture):

Done!

wp-admin December 16, 2017 Launch X431 ToolsLaunch X431 Pro Mini, Launch X431 Pro Mini Bluetooth, Launch X431 Pro Mini OBD2 Diagnostic Scan Tool, Launch X431 PRO MINI WIFI Bluetooth, X431 Pro Mini 0 Read more >

2017 Launch X431 Pro Mini review – newer & better than many tools

I’m a Launch user living Canada, and couldn’t be happier with this Launch X431 Pro Mini Bluetooth. I would like to write an objective review on X431 Pro Mini here. I really highly recommend it for following reasons.

X431 Pro Mini unit is small, the smallest of the Auto Scanner Tools that I’ve dealt with. This tool is the newest Launch product out on the market for 2017. I took a big risk in buying X431 Pro Mini because it wasn’t released in North America. But good thing it worked out because the updates for the software are newer than the ones in North America. Example: on the X431 pro Mini Porsche firmware V21.91. In current software from launchtechusa.com/ North America it’s V21.81.

It’s all about the software, doesn’t matter where these machines are made, the software has to be current.

Previously I had the older Launch GDS which gave me issues with Acura, Honda, Toyota and Nissan. Thank god the issues have been fixed with this new X431 pro Mini unit. By far, the BMW, Benz and VW software is the best you can find on the market. I used and bought previous Snapon- Verus, Autel and PIWIS, Vagcom. This X431 pro Mini tool by far is one of best well-rounded ones. The customer service from www.cnautotool.com is very nice and helpful too, they are prompt at answering any questions. The shipping also came on time! Faster than I expected.

wp-admin November 3, 2017 Autel Tools, Auto Scanner Tools, Car Diagnostic Tools, Launch X431 ToolsLaunch X431 Pro Mini, Launch X431 Pro Mini Bluetooth, Launch X431 Pro Mini OBD2 Diagnostic Scan Tool, Launch X431 PRO MINI WIFI Bluetooth, X431 Pro Mini 0 Read more >

Launch X431 V 8″ full-system scanner needs no authorization no IP limitation

Launch X431 V 8” Lenovo Tablet full-system diagnostic tool does not need to authorize by sending SN, Country and Language to the seller and wait 2 working days, also registration has no IP limitation (Except China) with dealer code 755D. Moreover, full range car models and full car system diagnosis make X431 V a professional automotive diagnostic tool.

Launch X431 V 8inch Tablet inherits many advantages of X-431 V 7″ such as the full-system diagnosis and full range car models, communicate via Wifi /Bluetooth etc., meanwhile it improve in specification and vehicle coverage compare with X-431 V 7″ (X431 Pro) (for more Launch X431 V 8″ compare X431 V 7″ , go to read in the last paragraph).

X431 V 8” diagnostic scanner is powerful and user-friendly:

1.Performfull-system diagnosis by pairing DBSCAR adapter to Bluetooth (same as X431 V 7″)
2.Support up to 69 car brands about 220 car models from European, USA and Asian;
3.With 2–year free updateon the official site com (same as X431 V 7″)
4.Android 4.2 platformwith fast running speed, clear and user-friendly interface
5.Take advantage of android system, it integrates more application and service, such as creating maintenance data base and case library, providing instant maintenance information, establishing public and private maintenance social circle etc.
6.Reasonable PDA designand easy to carry.
7.Wifi:Built-in Wi-Fi module makes surfing on the internet freely (same as X431 V 7″);
8.Bluetooth: Communicate via Bluetooth (same asX431 V 7″)
9.Registration with dealer code: 755D, has no IP limitation, no need send country, language for activation and wait 2 working days, you could directly use.

Launch X431 V 8” surpasses other similar diagnostic scanners in the following aspects:

1.Full Diagnosis Function:

Launch X431 scan tool V is able to diagnose the electronic control system of worldwide vehicle models covering Asian, European, American and Chinese. Full range car models and full car system diagnosis make it a professional automotive diagnostic tool.

Diagnosis functions include: Read DTCs, Clear DTCs, Read DataStream, Special functions etc;

2.Special function:

X431 V is with special function such as BMW idle study, BMW injection rate adjustment, BMW battery replacement, Nissan matching key.

3.X431 V 8”connectivity: via Bluetooth, Bluetooth distance: 10M (Without Obstacle)

You could use GOLO connector to connect to the smart phone, then you can do all system fault diagnosis of vehicle at any time, then form a diagnosis report, and transfer the report to maintenance technicians and related personnel through the account management interface, then he get the remote consultation and repair advice.

4.Launch X431 V 8”language available: English, German, Japanese, Russian, French, Korea, Arabic, Spanish and Traditional Chinese

Launch X431 V 8″ Tablet menu:
Click the “Settings” to configure the personalized X-431 V;
Click “Search” to locate your target quickly and conveniently;
Click “Email” to send and receive email. External POP3 or IMAP email account for some common Web email service provider can be added;
Click “File Manager” you can manage the files or downloaded files stored in SD card efficiently;
Other Additional Functions: Alarm, calendar, calculator etc.

X431 V 8″ Specifications:
Other android-based applications can be customized to install or uninstall.
Operating system: Android 4.2
CPU: 1.3 GHz
Display: 8” TN capacitive touch screen
RAM: 1 GB
Capacity (internal / SD card):16GB
Battery: 4290 mAh
Printer: Optional (Wi-Fi)
Camera: Front 2 mp / Back 5mp
Communication: WiFi/Bluetooth

Package includes:
1pc x X-431 v pad computer
1pc x Password envelope
1pc x X-431 v protection sleeve
1pc x DBScar diagnostic connector
1pc x OBD II extension cable
1pc x Cigarette lighter cable
1pc x Power adaptor
1pc x USB data cable
1pc x Non-16pin connector

X431 V 8″ full-system scanner (SP183-D) surpasses X431 V 7“ (SP183) in specification and vehicle coverage:

1.Outlook difference:
They have different outlook
Here X431 V 7″ mux

2.Specification difference
X431 V 7″ CPU: Dual core 1GHz x431 (X431 V 8” CPU 1.3 GHz)
X431 V 7″ LCD: 7.0 inch (X431 V 8” LCD is 8.0 inch)

3.Dear code difference
X431 V 8” dealer code: 755D
X431 V 7” dealer code: 86A or 86K

4.Activation difference
X431 V 7” needs to active by sending machine SN, country, language to active and wait 2 working days.

5.Vehicle coverage difference
X431 V 7”: covers up to 59 car brands from European, USA and Asian
X431 V 8”: covers up to car brands about 220 car models from European, USA and Asian

6.Language difference
X431 V 7”:
English,German,Japanese,Russian,French,Spanish,Portuguese,Polish,Turkish,Dutch,Greek,Hungarian,Arabic,Danish,Korean,Persian,Romania,Serbian,Finnish,Swedish,Czech,Simplified Chinese,
traditional Chinese

X431 V 8” from www.cnautotool.com: English, German, Japanese, Russian, French, Korea, Arabic and Spanish

wp-admin September 19, 2017 Launch X431 ToolsLaunch X-431 V+, Launch X431 V 8 inch, Launch X431 V 8inch Tablet, Launch X431 V 8″, Launch X431 V Bluetooth, Launch X431 V Bluetooth Wifi, Launch X431 V Wifi, Launch X431 V+, Launch X431 X-431 V, X-431 V+, X431 pro, X431 V 8inch, X431 V+ 0 Read more >

Launch X431 V 8″ tablet scanner user guide carlist, update, how to, compare

This post put together all Launch X431 V 8 inch tablet user guide i.e car list, special functions work, how to register, how to update, how to use on a specific car, comparison with other similar tools, user manual,etc.

1.Launch X431 V 8″ tablet scanner carlist at CnAutotool.com

Works on: Indian cars, Australian cars, Malaysian cars

This is Launch Vehicle Coverage Inquiry System: http://qcar.x431.com/serial/layout.action

2.Launch X431 V 8″ tablet scanner special functions work:

Brake reset, oil reset, SAS reset, BAT reset, bleeding, Elec.trottle RLRN, TPMS reset, DPF Reg, Gear learn, IMMO

3.Launch X431 V 8″ tablet scanner register

4. Launch X431 diagnostic tool V 8″ tablet activation:

Does not need to active any more.

5. Launch X431 V 8″ tablet scanner update:

2 years free update online
Download and update the newest diagnostic .apk at http://www.dbscar.com/

FAQ:
Q: The “Diagnostic” icon is deleted, how to restore it?

Answer: click official site: http://www.dbscar.com/, login with your ID and password, click on “Download software” then “V for Android” to download the newest .apk.Actually, the Launch X431 V 8inch package includes a “Quick Start Guide (EN) and user manual follow it to operate.