Tag Archive: Mb Star C4 with EVG7 Tablet

MB SD Connect C4 WIFI set on WIN10 laptop Xentry 03.2017 OK

Here share with you a personal tested guide, hope it helps and try your own risk!
How to set up MB Star C4Wireless on a Dell XPS15 9550 laptop WIN10 and run Mercedes Xentry 03.2017 software?
2-1
I’m running Win10 on a Dell XPS15 9550 laptop with Intel AC 8260 internal wireless card installed.

After days of investigation and testing, the most important thing is that: The drivers for your wireless card MUST support AdHoc functionality.

This can be verified at the DOS command prompt. The command is: Netsh wlan show drivers
This command will show “Yes” or “No” on the line for “Hosted Network Support”.
If this line says “No”, AdHoc will not work properly.
Although I’m running Win10, Intel has drivers for the 8260 wireless card for Win8 which will enable proper AdHoc functionally.

The trick is to download the driver first, prior to removing your existing wireless driver. Download the driver ONLY, not any driver file with additional driver management apps included in the downloaded file.

Now you can go into Device Manager and remove your existing wireless card AND check the box that removes all software associated with it. My Win8 driver download file was a .exe file. I double clicked on it and the Win8 driver for my Intel 8260 card was installed. Went to Device Manager, right clicked on my 8260 wireless card and selected Properties. Clicked on Advanced and was able to see several AdHoc related entries. These AdHoc entries were not visible using the Win10 drivers.

AdHoc can now be verified at the DOS command prompt. The command is:
Netsh Wlan show drivers.
This command will show “Yes” on the line for “Hosted Network Support”.
If this line says “No”, AdHoc will not work properly

With AdHoc functionality confirmed, additional DOS commands can now be used to enable Road24h wireless connectivity.
This is what worked for me. Depending on your computer skills, your results may vary.

P.S. Recommend to get  MB DAS Xentry HDD 03.2017 for WIN7 or WIN10, WIFI set on WIN10 100% OK!

2-2

To know more information from www.cnautotool.com.

MB SD C4 Tourismo bus communication error (fixed)

I bought the MB SD C4+Dell D630 Laptop pre-installed bundle, when I test it have the problem Mb Star C4 cannot power on when connected with Mercedes Tourismo bus, I contacted there customer service at cnautotool.com, and here is the solution provided by their engineer.

I will explain my problem in detail:

” I have tried 2 different mb sd connect c4 on Tourismo buses and sd connect does not power on.In the meantime those MB SD Connect C4 works normally to any other MB Truck and car.also on Tourismo have check MB Star C3 and works normally.”

You should check:

bus with OBD
pin 4 + 5
both must be connected and ground

In SDConnect “-” is 5 pin only. There is 4 contact not used in 16pin OBD connector.

“i’m getting an communication error when connecting xentry to a Mercedes tourismo.”

4-1

A Communication error has occurred when access FPS system

4-2
4-3
Solution:

– turn OFF/ON BUS ground switch (our remove battery – cable). FPS1 wake up and MB Star diagnostic recognized FPS1/VIN code.

or

– enter the DAS ATEGO truck come and place manually and then it will work perfect

” Another problem is : “Currently the speed limit is set to 100 km/h. I’m trying to set it to higher value (with Mercedes Star Diagnosis MB SD C4 DAS using modified EOL files). On the menu it tells me that I can, because there are higher values (105 km/h. 112 km/h, etc). But when I try to set the speed limit to higher than 100 km/h it doesn’t allow me to do it (can’t save the changes). When I try to set it below 100 km/h everything goes fine.”

I done the Access special settings , and it working perfect now!