Tag Archive: CAT Diagnostic Tool

Diagnostic Codes on Caterpillar ET Software

Diagnostic Capabilities

Diagnostic Codes
The CAT Caterpillar ET engine’s Electronic Control Module (ECM) has the ability to monitor the circuitry between the ECM and the engine’s components. The ECM also has the ability to monitor the engine’s operating conditions. If the ECM detects a problem, a code is generated.

Diagnostic-Codes-on-Caterpillar-ET-Software

There are three categories of codes:
-Diagnostic Code
-Event Code
-Flash Code

-Diagnostic Code – A diagnostic code indicates an electrical problem such as a short or an open in the engine’s wiring or in an electrical component.
-Event Code – An event code is generated by the detection of an abnormal engine operating condition. For example, an event code will be generated if the oil pressure is too low. In this case, the event code indicates the symptom of a problem. Event codes indicate mechanical problems rather than electrical problems.
-Flash Code – Diagnostics and events are reported via flash codes. When a diagnostic code or an event code becomes active, the specific condition is immediately reported to the operator through a series of flashes on the diagnostic lamp. By counting the flashes, a numeric representation of the diagnostic code or event code is revealed.

Codes can have two different states:
-Active
-Logged
-Active Codes
An active code indicates that a problem is present. Service the active code first. For the appropriate
troubleshooting procedure for a particular code, refer to the following troubleshooting procedure:
a. Troubleshooting, “Diagnostic Trouble Codes”
b. Troubleshooting, “Event Codes”
Refer to the Troubleshooting, “Diagnostic Code Cross Reference” for information that relates to converting flash codes to the equivalent diagnostic code or to the equivalent event code.

-Logged Codes
The codes are logged and stored in the ECM memory. The problem may have been repaired and/or the problem may no longer exist. If the system is powered, it is possible to generate an active diagnostic code whenever a component is disconnected. If the component is reconnected, the code is no longer active but the code may become logged.
Logged codes may not indicate that a repair is needed. The problem may have been temporary. Logged codes may be useful to help troubleshoot intermittent problems. Logged codes can also be used to review the performance of the engine and of the electronic system.

Current Totals on Caterpillar ET Software

Current Totals on Caterpillar ET Software

-Connect CAT ET Diagnostic Software
,
-Information – Current Totals,

Current Totals:
-Total Operating Hours (hours)
-Total Idle Time (hours)
-Total Fuel (Gal)
-Total Idle Fuel (Gal)
-Total Max Fuel (Gal)
-Average Load Factor (%)

Caterpillar Flash Files 10.2017 Download

CAT Caterpillar ET Flash Files are used to flash Caterpillar ECM memory.You need use Caterpillar Electronic Technician software to communicate with ECM,and then load the CAT flash file to flash.

It include:

FL2 file,FLS file,CFG file,CNF file,IQA file,SRC file,SMP file,LHX file,IDT file,OPT file,IDA file,SG5 file,HEX file,SG4 file,GCIBIN file,MCH file,SMP file,Other…

Below picture only show part of the file,all file over 9000+,after extract two iso file it about 13GB.

Caterpillar-Flash-Files-10.2017-Download Caterpillar-Flash-Files-10.2017-Download-1
Caterpillar-Flash-Files-10.2017-Download-1

Caterpillar ET 2019A Electronic Technician Software Free Download

What is Caterpillar ET?

CAT Electronic Technician (Cat ET) is diagnostic software required to communicate, diagnose and service electronically controlled Caterpillar engines and machines. When connected to an Electronic Control Module (ECM), a technician has the ability to diagnose existing and potential problems, configure the product, and obtain data for analysis.

Caterpillar-ET

Caterpillar ET Electronic Technician Software Free Download

Diagnostic Tools for Truck Caterpillar ET Functions List:

1.View active and logged diagnostics.

2.View events where irregularities occurred and were logged by the ECM.

3.View the status of a group of parameters (temperatures, pressures, etc.) simultaneously.

4.Record and log performance data.

5.Graph a group of status parameters.

6.View the current configuration of an ECM.

7.Change ECM configurations.

8.Perform diagnostic tests.

9.Perform calibrations.

10.Print reports and diagnostic results.

11.Please keep in mind that some ecm settings for example, speed limit requires factory password. The factory password generator is not included in this application

Caterpillar ET Support Languages:

English,Chinese,Danish,French,German,Italian,Portuguese,Spanish

Caterpillar ET Support OS:

Window 7,Window 8,8.1,Window 10 32 bit and 64 bit

PC Requirements

Recommended Configurations

PC containing a 2.0 GHz dual-core processor·

3GB RAM·

3GB of available hard disk drive·

DVD-ROM drive·

15.4 inch XGA Screen (1280×1024 compatible)·

MicrosoftòWindows 7 Professionalor Windows 8 Professional

(Note: Windows 8 RT is not supported)·

RS232 port with 16550AF UART or compatible (for use with Comm Adapter II)·

USB 1.1 or 2.0 port (for use with Comm Adapter 3)·

Ethernet RJ45 connector·

Built in pointing device or mouse·

For security purposes, MicrosoftòInternet Explorerversion 9 or newer is recommended.

Note: The most recent version of MicrosoftòInternet Explorer may not be validated to work with the service tool.

Minimum Configurations

PC containing a Pentium 2 GHz processor or greater·

1GB RAM·

500MB of available hard disk drive·

CD-ROM drive·

Super VGA monitor or display (1024×768)·

MicrosoftòWindows 7 Professional or Windows 8 Professional

(Note: Windows 8 RT is not supported)·

RS232 port with 16550AF UART or compatible (for use with Comm Adapter II)·

USB 1.1 or 2.0 port (for use with Comm Adapter 3)·

Ethernet RJ45 connector·

Built in pointing device or mouse·

For security purposes, MicrosoftòInternet Explorer version 9 or newer is recommended.

Note: The most recent version of MicrosoftòInternet Explorer may not be validated to work with the service tool.

Caterpillar ET Free Download

Caterpillar ET 2019 A

https://mega.nz/#!zIZUDARZ!q8wQWzgM9CeZrxZdp5VhaFCRULvv_b_ENE0e1Oe_UHM

How To Get CAT Caterpillar ET 2010A License Key

Step1: Caterpillar Open Electronic Technician

How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-1

Step 2: Caterpillar Electronic Technican Asks for License

How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-2

Step 3: Caterpillar ET 2010A Asks for Licensing

How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-3

Step 4: Copy License Code

How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-4

Step 5: Open CAT ET Key 2010A

How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-5

Step 6: Open ” et2k9c.kg”

How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-6

Step 7: Caterpillar ET 2010A Paste License Code
How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-7

Step 8: Caterpillar ET 2010A Choose Subscription
How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-8

Step 9: Caterpillar ET 2010A Copy License Key

How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-9

Step 10: Caterpillar ET 2010A Copy License Key
How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-10

Step 11: Paste License Key in The Following Box

How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-11

Step 12: Click Authorize
How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-12

Step 13: Caterpillar ET 2010A Copy License Granted

How-To-Get-CAT-Caterpillar-ET-2010A-License-Key-13

Create Product Status Report (Download List) on Caterpillar ET Software

How to Create Product Status Report (Download List) on CAT Electronic Technician Software?

-Open Caterpillar ET Software, Click on Menu “Information – Product Status Report”, and Mark on “Download List”.

Create-Product-Status-Report-on-Caterpillar-ET-Software

-Click on “Create Report”, wait until process complete, and Click “Save As” to Save Product Status Report file to your documents (.xml)
-Example Product Service Report Download (pdf format);

Top 4 reasons to get Caterpillar ET Software Caterpillar Electronic Technician

If you want to install the software by yourself and activate multiple computers, please purchase software with a keygen.(2019A Cat Caterpillar ET 3 Software With KeyGen Activation and Installation Video)

Top 4 reasons to get CAT Caterpillar ET Software Caterpillar Electronic Technician:
1.Latest Caterpillar ET Software to work with CAT/CAT3 Truck Scanner
2.With one free activation, can send software online
3.Support Multi-languages:English, Chinese, Danish, French, German, Italian, Japanese, Portuguese, Russian, Spanish
4. SO: Win 10, Win 8, Win 7, Win Vista, Win XP

Cat-Caterpillar-ET-2018A-2018C-2019A-Software-1 Cat-Caterpillar-ET-2018A-2018C-2019A-Software-2

Cat et Caterpillar Electronic Technician Software:
Type of catalogue: Caterpillar Electronic Technician Diagnostic Software
Make: Caterpillar
Region: WorldWide all region
Operating System: Windows 7 32 bit, Wnidows 7 64 bit, Windows 8/8.1 32 bit, Windows 8/8.1 64 bit, Windows 10 32 bit, Windows 10 64 bit

Cat et Diagnostic Software PC Requirements:

Recommended Configurations:
PC containing a 2.0 GHz dual-core processor
3GB RAM
3GB of available hard disk drive
DVD-ROM drive
15.4 inch XGA Screen (1280×1024 compatible)
Microsoft Windows 7 Professional or Windows 8 Professional, Windows 10 Professional (Not tested with Home Edition) (Note: Windows 8 RT is not supported)
RS232 port with 16550AF UART or compatible (for use with Comm Adapter II)
USB 1.1 or 2.0 port (for use with Comm Adapter 3)
Ethernet RJ45 connector
Built in pointing device or mouse
For security purposes, Microsoft Internet Explorer version 9 or newer is recommended.

Caterpillar ET Software Function:
This diagnostic app allows you to:
View active and logged diagnostics.
View events where irregularities occurred and were logged by the ECM.
View the status of a group of parameters (temperatures, pressures, etc.) simultaneously.
Record and log performance data.
Graph a group of status parameters.
View the current configuration of an ECM.
Change ECM configurations.
Perform diagnostic tests.
Perform calibrations.
Print reports and diagnostic results.
Please keep in mind that some ecm settings for example, speed limit requires factory password. The factory password generator is not included in this application
PC, Communication Hardware, and Cable Requirements
To run the service tool, the next PC, communication hardware, and cable requirements must be met. NOTE: The minimum PC Configurations should not be used as a standard when buying new personal computers for service tool purposes. If the existing equipment meets these minimum requirements, it will run the service tool.
PC Requirements
Recommended Configurations
PC containing a 2.0 GHz dual-core processor
3GB RAM
3GB of the available hard disk drive
DVD-ROM drive (optionally)
15.4-inch XGA Screen (1280×1024 compatible)
Microsoft Windows 7 Professional or Windows 8 Professional, Windows 10 Professional (Not tested with Home Edition) (Note: Windows 8 RT is not supported)
RS232 port with 16550AF UART or compatible (for use with Comm Adapter II)
USB 1.1 or 2.0 port (for use with Comm Adapter 3)
Ethernet RJ45 connector
Built-in pointing device or mouse
For security purposes, Microsoft Internet Explorer version 11 or newer or Microsoft Edge is recommended.
Note: The most recent version of Microsoft Internet Explorer may not be validated to work with the service tool.
Wi-Fi (for the Wireless Comm Adapter 3)

Minimum Configurations
PC containing a Pentium 2 GHz processor or greater
1GB RAM
500MB of an available hard disk drive
CD-ROM drive
Super VGA monitor or display (1024×768)

Microsoft Windows 7 Professional or Windows 8 Professional, Windows 10 Professional (Not tested with Home Edition) (Note: Windows 8 RT is not supported)
RS232 port with 16550AF UART or compatible (for use with Comm Adapter II)
USB 1.1 or 2.0 port (for use with Comm Adapter 3)
Ethernet RJ45 connector
Built-in pointing device or mouse
For security purposes, Microsoft Internet Explorer version 9 or newer is recommended. Note: The most recent version of Microsoft Internet Explorer may not be validated to work with the service tool.
Communication Hardware
Caterpillar Communication Adapter III
Configuring Cat Electronic Technician to use the Communication Adapter 3
For Cat Electronic Technician to work with the Communication Adapter 3, the settings must be changed to select the
Communication Adapter 3 as the Communication Interface Device:
Step 1 Start Cat Electronic Technician.
Step 2 Click the Stop Connect button when it appears.
Step 3 Select the Utilities menu.
Step 4 Choose “Preferences > Modify…”.
Step 5 Select the Communications tab.
Step 6 Select Cat Comm Adapter 3 (RP1210) and click OK.
NOTE: Because a growing number of products require multiple data link service, the “Enable Dual Datalink Service” checkbox has been pre-selected.

Servicing ECMs on more than one data link requires this check box to be enabled.
Failure to do this will result in undetected ECMs and reduced functionality.

What’s New
What’s New – 2019A
ECM Naming Changes
Certain ECMs connect to the service tool over two data links at the same time. The service tool shows a message popup when the ECM is only detected on one link. The service tool has been changed to add the text **INCOMPLETE** in the ECM name when the connection is incomplete. Service tool features that display a connection icon also use a new icon for an incomplete connection.

Cat-Caterpillar-ET-2018A-2018C-2019A-Software-3
What’s New – 2018C
No significant new features or feature enhancements

Cat-Caterpillar-ET-2018A-2018C-2019A-Software-5

What’s New – 2018B

CEOS Fleet Configuration File TOP

A CEOS (Customer Electronic Option Selection) Fleet Configuration File can be created/modified for an engine using the Service Tool. This is available in connected and disconnected mode.

Error When Launching Service Tool

There is a Microsoft issue with upgrading libraries during an installation involving certain versions of the C++ redistributable. After a successful service tool installation, when trying to run the service tool for the first time, one of the following errors may occasionally appear: “The entry point could not be located in api-ms-win-crt-runtime” or “The program can’t start because mfc140u.dll is missing from your computer.” If either of these messages is displayed, please let us know and we will send you to step by step troubleshooting guide. This procedure requires administrator rights.

Service Tool License Corruption Issues with Windows 10 Updates

Windows 10 updates 1709 and 1803 will corrupt service tool licenses. Future Window 10 updates may do the same

If either of license error messages is displayed, please let us know and we will send you to step by step troubleshooting guide.

What’s New – 2018A
Trainer Update – 988K XE Wheel Loader
The 988K XE Wheel Loader has been added to the Trainer application.

What’s New – 2017C
Preferences Option to Save a Product Status Report to PDF
The Preferences dialog for the Product Status Report has changed. The dialog contains a new checkbox to automatically save a Product Status Report as a PDF file when the report is created. The service tool will continue to automatically save Product Status Reports as an XML file.

What’s New – 2017B
Product Status Report Updates
The Product Status Report has been updated to include certain history features supported by the ECM, such as the after-treatment Regeneration History and the Service Test History.
Winflash Screen Update
The screen for the Winflash feature has been updated. A new Expand All button opens all sections of the screen to show all details for ECMs detected by WinFlash. A new Collapse All button hides all sections of the screen, except for header rows showing detected ECM names.

Package Includes:
1pc x Caterpillar ET 2018A or 2018C or2019A software (Can choose to send online)

Diagnostic Codes on Caterpillar ET Software

Diagnostic Capabilities

Diagnostic Codes
The engine’s Electronic Control Module (ECM) has the ability to monitor the circuitry between the ECM and the engine’s components. The ECM also has the ability to monitor the engine’s operating conditions. If the ECM detects a problem, a code is generated.

一张

There are three categories of codes of CAT Electronic Technician:
-Diagnostic Code
-Event Code
-Flash Code

-Diagnostic Code – A diagnostic code indicates an electrical problem such as a short or an open in the engine’s wiring or in an electrical component.
-Event Code – An event code is generated by the detection of an abnormal engine operating condition. For example, an event code will be generated if the oil pressure is too low. In this case, the event code indicates the symptom of a problem. Event codes indicate mechanical problems rather than electrical problems.
-Flash Code – Diagnostics and events are reported via flash codes. When a diagnostic code or an event code becomes active, the specific condition is immediately reported to the operator through a series of flashes on the diagnostic lamp. By counting the flashes, a numeric representation of the diagnostic code or event code is revealed.

Codes can have two different states:
-Active
-Logged

-Active Codes
An active code indicates that a problem is present. Service the active code first. For the appropriate
troubleshooting procedure for a particular code, refer to the following troubleshooting procedure:
a. Troubleshooting, “Diagnostic Trouble Codes”
b. Troubleshooting, “Event Codes”
Refer to the Troubleshooting, “Diagnostic Code Cross Reference” for information that relates to converting flash codes to the equivalent diagnostic code or to the equivalent event code.

-Logged Codes
The codes are logged and stored in the ECM memory. The problem may have been repaired and/or the problem may no longer exist. If the system is powered, it is possible to generate an active diagnostic code whenever a component is disconnected. If the component is reconnected, the code is no longer active but the code may become logged.
Logged codes may not indicate that a repair is needed. The problem may have been temporary. Logged codes may be useful to help troubleshoot intermittent problems. Logged codes can also be used to review the performance of the engine and of the electronic system.

FREE License Key for Caterpillar ET (Electronic Technician) Software

1. First Step, install CAT Caterpillar ET Software: ET_2010A_v1.0, wait until Status is complete.
Electronic - Technician - 1

2. Second Step, Open Caterpillar ET through shortcut on Desktop or Start Menu/ All Program, double click on Electronic Technician.
After Software opened, will showing a Message Box as below;

Electronic - Technician - 2

NOTE: Software is Not Licensed, then Click YES..

Electronic - Technician - 3

Yap, I have Software to Generate License Key, Full Service Dealer ET

Electronic - Technician - 4

Please comment your License Code, I will give you License Key to activate your Electronic Technician Software.

Diagnostic Codes on Caterpillar ET Software

Diagnostic Capabilities

Diagnostic Codes
The engine’s Electronic Control Module (ECM) has the ability to monitor the circuitry between the ECM and the engine’s components. The ECM also has the ability to monitor the engine’s operating conditions. If the ECM detects a problem, a code is generated.

Diagnostic - Codes - on

There are three categories of codes:
-Diagnostic Code
-Event Code
-Flash Code

-Diagnostic Code – A diagnostic code indicates an electrical problem such as a short or an open in the engine’s wiring or in an electrical component.
-Event Code – An event code is generated by the detection of an abnormal engine operating condition. For example, an event code will be generated if the oil pressure is too low. In this case, the event code indicates the symptom of a problem. Event codes indicate mechanical problems rather than electrical problems.
-Flash Code – Diagnostics and events are reported via flash codes. When a diagnostic code or an event code becomes active, the specific condition is immediately reported to the operator through a series of flashes on the diagnostic lamp. By counting the flashes, a numeric representation of the diagnostic code or event code is revealed.

Codes can have two different states:
-Active
-Logged

-Active Codes
An active code indicates that a problem is present. Service the active code first. For the appropriate
troubleshooting procedure for a particular code, refer to the following troubleshooting procedure:
a. Troubleshooting, “Diagnostic Trouble Codes”
b. Troubleshooting, “Event Codes”
Refer to the Troubleshooting, “Diagnostic Code Cross Reference” for information that relates to converting flash codes to the equivalent diagnostic code or to the equivalent event code.

-Logged Codes
The codes are logged and stored in the CAT Electronic Technician. The problem may have been repaired and/or the problem may no longer exist. If the system is powered, it is possible to generate an active diagnostic code whenever a component is disconnected. If the component is reconnected, the code is no longer active but the code may become logged.
Logged codes may not indicate that a repair is needed. The problem may have been temporary. Logged codes may be useful to help troubleshoot intermittent problems. Logged codes can also be used to review the performance of the engine and of the electronic system.