Monthly Archive: July 2019

How to Solve the Problem NEXIQ-2 USB Link + Software can’t run keygen ?

NEXIQ-2 Support Heavy-Duty, Light-and Medium-Duty Trucks, CONSTRUCTION EQUIPMENT like (Wheel loader, Articulated Hauler and Excavator), Genset.

Some customers have the problem that the software can’t run keygen , please check the pictures as bellow :

Need to active :

Cummins insite 7.5 :

Pc id : 43873FA7

Caterpillar E.T . :

License code : 3295 668C 8D56 CE1E CD16 4E7C



Version : 07.05-01301-00000

Computer ID : E8-BE-28-1E-2D


DDDL doesnt need to active but operate in the crack method ( You can check the instructions in the CD )

Any other request , welcome to contact us at

Or check more products on our website


Solution to John Deere 4.2 error ” Application not found”

When installing John Deere 4.2, someone may run into an error ” Application not found” (Please look at the below image)

Application - not - found


Solution 1: use virtual drive software (alcohol120 or clonedrive) to setup JD SA. don’t start installation from a folder with extracted files.

Solution 2 (Supplied by engineer)

For John Deere Service Advisor 4.2, the software is contained in one Hard disk, just plug the hard disk into the computer, start the program, then contact the supplier for remote activation.

How to Program CGDI ELV Emulator with CGDI MB Step by Step

How-to: program CGDI ELV Emulator with CGDI Prog MB Benz key programmer step by step.


In CGDI MB Software, choose Compute Password option->Collect Data-> The 1 generation key
We start with insert key in EIS
Remove key and insert it in CGDI IR shown as picture
We have to wait till its is 100% loaded without touching the key

Remove key from CGDI MB and insert it back in EIS

Pull key out of EIS

Reinsert key into EIS

Pull key out and count to 5 seconds then insert it back again, then press OK

Insert key into CGDI IR

Save generated data, choose wherever you want to save data

Then we can upload the data to server

Press Query Result and wait till the password is calculated

Calculate pass success. Press Copy button

We choose EIS now and press Read EIS Data
Then paste the copied password previously

Save EIS data

Now we go to ELV option
Choose Simulator
Load EIS data saved previously

Press Write

It will give you message Connect the yellow Kline from the OBD cable to the CGDI ELV emulator

Writing success, now you can use the emulator
Turn on ignition switch to activate it.


FVDI 2018 Changes BMW E91 CAS3+ Odometer by Dump

How-to: correct odometer on a CAS3+ BMW E91 with 2018 FVDI ABRITES Commander commander by dump.
Vehicle model: E91
Chip: 0L15Y
Cluster type: Siemens VDO
Main steps:
Step 1: Read dump
Step 2: Write KM
Step 3: Flash new file to IMMO
Step 1: Read CAS3+ Dump with Xhorse VVDI Prog
In VVDIProg software, select BMW CAS3+ 0L15Y
Make connection following the wiring diagram
fvdi-change-bmw-e91-cas-km-3 fvdi-change-bmw-e91-cas-km-4
Read and save CAS3+ dump
fvdi-change-bmw-e91-cas-km-5 fvdi-change-bmw-e91-cas-km-6
Step 2: Change KM with FVDI 2018

Connect 2018 FVDI commander with laptop
Open software and select VVDI2 function (FVDI 2018 comes with free VVDI2 VAG/BMW function)
Select BMW V1.2.2->Special Function->File change KM->Select type: CAS3+ (0L15Y, 0M23S)->Load EEPROM dump file
fvdi-change-bmw-e91-cas-km-7 fvdi-change-bmw-e91-cas-km-8 fvdi-change-bmw-e91-cas-km-9
Upload dump file read by vvdi-prog
Load file success. Check the old KM
Manually enter new KM you desired and press Change KM
Save new EEPROM dump file

Change KM in immobilizer success.
Step 3: Flash the new file into IMMO ECU
You must change KM in instrument dashboard manually before connect IMMO ECU to car.
Go back to VVDI Prog, write immo with the new dump file into IMMO.
Reinstall IMMO box and back to vehicle.
Check the new KM changed.

Rent Mercedes-Benz Online SCN Account

Rent SCN code to access user name and password.

The link

You can rent login name and password monthly or annually. You can also enter it in turn (through team viewer).
Calculating Radio Anti-theft PIN Code
Online Enabling FBS4 Key

Mercedes-Benz-1 Mercedes-Benz-2

scn coding meaning:

Software Calibration Number coding, short for SCN coding is intrudes by MB around 2005. It replaced the previous coding technique with a centralized and almost automated technique to prevent incorrect coding being selected when replacing a module.

scn online coding instruction:

Here is the online SCN coding guide.

Configure MB STAR:
Come to “SDnet Control” menu>> Configuration >>Network: workshop cable network>> Place a checkmark next to “Automatically obtain IP address”
To check the active Internet connection, select Star Browser. The registration window for the after-sales platform should open. Enter the Service Name and password if request.
Connect MB STAR diagnostic system with vehicle
Start STAR DAS software program
Select Benz model and make: Vans>>V-Class >>Sprinter>>Model designation>>Vehicle recognition. If the vehicle is not recognized, enter the required data manually (e.g. Germany, Rest of World)
Entry for retrofits and modifications – Select “Online” (“networked Star Diagnosis device”)
Change or enter the vehicle equipment codes: + ED5 (PSM installed), – ED8 (PSM preinstallation).
NOTE: If the vehicle does not have a preinstallation (ED8), ED8 does not need to be changed to ED5.
Run a Quick test
Come to the EIS (electronic ignition starter switch) control unit>> Control unit adaptation >>SCN coding >>Select the “Online (networked Star Diagnosis unit)” menu option
SCN coding will start automatically (visible on the progress bar on the screen). Please strictly follow the STAR diagnostic software instructions. Otherwise the control unit may be destroyed during the coding procedure.
When the system display a comment “The coding variant has been changed”, the SCN coding is completed. The parameterization has been completely taken over in the EIS and is thus finished.

How does CGDI BMW diagnose BMW 3 series E93 successfully?

Confirmed: CGDI BMW adds “BMW diagnosis” to be able to program and code BMW E series; able to read/clear trouble codes for BMW E series, F series, G series.

How to update CGDI BMW diagnosis function for free:

As long as you have any of CG100 or CG PRO or CGDI MB, please provide the serial number for free trial.


1.Easy to use. As long as you are qualified with corresponding vehicle maintenance knowledge, CGDI BMW does not have high requirements for the user’s professional skills and English level.

2.Cheap. CGDI BMW is cheaper than BMW ICOM (clone and original).

BMW ICOM clone & original are able to diagnose, program and code BMW E-series models at higher price (clone: about 400eur).

Besides, BMW ICOM has some requirements for the user’s operating skills during installation, therefore some users will choose a hard disk with pre-installed software and be charged.

3.Menu-driven & automatic operation instead of manual operation, which save much time.

How does CGDI BMW diagnose BMW 3 series E93 successfully?

1.Select “BMW diagnosis”.


2.It pops up “Whether to scan vehicle quickly”.

Press “Yes” and CGDI BMW will scan the BMW in 30 seconds.

Press “No” and CGDI BMW will scan the BMW all systems and take about 3 minutes.


3.After selecting “No”.

series-e93-3 series-e93-4

4.It pops up the BMW information.

Have diagnosis options :

Read fault codes, clear fault codes, Clear all codes, Help, back.

It is menu-driven operation, easy to use.

At the left corner, you will see the working status.
series-e93-5 series-e93-6 series-e93-7

5.Back to select “BMW diagnosis”, then “scan vehicle quickly”.

And you will see all trouble codes are cleared, and all are normal.

series-e93-8 series-e93-9 series-e93-10

Don’t you think it is easy to use CGDI BMW Prog for diagnosis?

How to update Lexia 3 version B to version C

I bought my Lexia interface clone from ( full chip with S/N 963830 C ) I tested as it is before reflash it with Mr. NLC and in some cars that I know 100% that a “B” clone didn’t worked before this “C” clone didn’t worked too.
Then I tested it again in same cars after I flashed with Mr. NLC And all worked 100%

Here is what I did:

Open the “” with a HEX Editor and read what Mr. NLC wrote in it.
I use my tool from time to time but what I wanna tell you is that when I bought my clone from china ( full chip with S/N 963830 C ) I tested as it is before reflash it with Mr. NLC and in some cars that I know 100% that a “B” clone didn’t worked before this “C” clone didn’t worked too.
Then I tested it again in same cars after I flashed with Mr. NLC
And all worked 100%
I took my clone for a long now so I do not remember when I did this tests but if I remmebr well was in May 2013
This are my tests that I did. What will be we will see. Conclusions are yours

If you wanna play you can edit the serial in the But take care.

Tip you might need:

For those have tried to update the firmware from B to C with the file i’ve been downloading from WP74, but it makes no difference in working, and you can’t access the C CAN bus:

The solution is: Just buy a standard 10K Ohms 1/4 watt resistor and solder it between the two terminals, similar to the form shown in the snapshot*.

* The snapshot is a random photo taken from the internet for demonstration purpose and not related to the XS Evolution VCI.


How to get car key data for cutting keys with SEC-E9 key machine

There are 3 ways to get auto key information with SEC-E9 key cutting machine

Key data can be gor by:

IC card

car model

key blank

in detail…

How to get key data by IC card on Key Programming tool SEC-E9 key machine:

1 go to “search” on the home page


2 press “KCode” and input the IC card you know, then “search”

3 go to “Menu” and read “Info”


4 check the data if they are what you want or not


How to get key info by model on SEC-E9 machine:

1 go to “Automobiles”


2 select a car make – model – year
sec-e9-key-machine-enter-key-data-ic-card-6 sec-e9-key-machine-enter-key-data-ic-card-7 sec-e9-key-machine-enter-key-data-ic-card-8

3 read key info


How to get key data by key blank on SEC-E9 key cutting machine

1 go to “Search”


2 input the key blank, then search

3 then you can get the key data


Free Download and Install JLR Mangoose SDD V157 Software and Patch

JLR SDD 157 software has been tested and verified working no issue with mangoose pro interfaces.

Software version: V157

Operating system: Windows XP/Windows 7

Multi-language: Chinese/Dutch/French/German/Italian/Japanese/Korean/Portuguese/Russian/Spanish

Compatible hardware: jlr mangoose/pro (SP116, SP205, SP205-B), mangoose vci (SP216, SP216-B)

Main steps:

Step 1: Install SDD setup

Step 2: Install Patch

Step 3: Install device driver

Step 4: Run SDD


Step 1: Install SDD setup

Open software CD/download software


Copy and paste JLR Driver folder and SDD Patch zip file to desktop
Run SDD_157_FULL as Administrator

Select setup language
Install wizard for SDD
Accept license agreement
Agree firewall compatibility warning
Choose destination folder: C://
Choose All languages pack to install

Install the program
If system prompts “Would you like ActiveCGM to be the default TIF viewer”, press NO

Install HV Safety installer

Finish install HV Safety installer setup

Install MOXA UPort Windows Driver Setup

Select destination location: C://Program Files/Moxa/USBDriver
Select Start Menu folder: MOXA UPort 1110 Series Windows Driver

Finish install windows driver

Install SDD setup completed.
Restart computer now.

Step 2: Install SDD Patch

Open SDD file, paste SDD folder to desktop

Open SDD folder
Run SDD as administrator

Check Notepad for user name and password
Run JLR SDD software on desktop as Administrator
Press Connection

Go to User Authentication interface

Copy user name and password and paste here
Press Identify

Enter dealer information
Crack the sdd software success

Close the SDD window

Step 3: Install device driver
Delete SDD Patch zip.file and SDD folder on desktop

Right click JLR SDD Properties,
open file location: C:/Program Files/JLR/Common/VCI Device Drivers/DrewTech Mongoose
Install J2534_MongoosePro_JLR_x86 driver
accept license agreement

Install j2534 driver completed
Connect JLR mangoose cable with laptop

Windows will automatically install driver

Go to Device Manager to check the interface is well connected

Step 4: Run SDD

Software is ready to use

Open JLR SDD software on desktop

Auto Read VIN

Run diagnostic function with SDD 157

install-jlr-sdd-v157-22 install-jlr-sdd-v157-23 install-jlr-sdd-v157-24 install-jlr-sdd-v157-25

Nissan Consult 3 Plus Programming Reviews: Cheapest way FOUND!

Nissan Consult 3 Plus programming reviews:

I looks like it’s a remote system using a bluetooth and is good up to 5 meters away. It also looks like it only works for OBD2…1996 and newer.

The Nissan Consult three Plus does not support the Q45’s made from 1990-1996 YET. I hope that changes soon.

I have an Infiniti G37 (2011). I used Nissan Consult III Plus to enter the pin and start programming new Key Fobs.

I was able to clear the existing keys , but am not able to program the new Fob(s).

The cheapest way to program Nissan:

No need a smart card!

I managed to do Immo and programming without spending out on the smart card.
find the consult diagnostictool.ini file
open with notepad
copy and paste this at the bottom




Here is the location of fille DIAGNOSTICTOOL.INI:


Please just try this at your own risk, I am not responsible the result if you have any question.

I share this because you can do this without spending money to buy the security card.

The best way to program Nissan:

If you can’t solve this problem, better buy a smart card for IMMO and PROGRAMMING.

Connect Consult 3 plus to the computer and the vehicle: Nissan Altima year 2006

Connection method: via the USB cable or Bluetooth

Insert key into the key hole, turn ignition ON with engine OFF

Start Consult-III plus software

Click on “Connect” button on VIMI selection screen to connect with VI


the computer and vehicle establish good communication

then Consult3 plus software will display VIN info

Choose Nissan model and year, and confirm vehicle information

Wait until the Nissan Consult module to access all control modules, Engine, BCM, Transmission, Airbag etc.

The car dashboard will illuminate and the indicator lights on Consult 3 will flash


Diagnostic: Direct Diagnostic Mode program

Tick Key programming icon (NATS SELECT DIAG MODE) on the left menu, plug the security card and press START

(There are two options under NATS SELECT DIAG MODE. Select C/U INITIALIZATION.


Push START BUTTON after enter password

Manually enter the pin code

Initialization completed

Follow the guide in the sw to finish key programming