obd2scantool.info

Tag Archive: CAT Caterpillar ET

Diagnostic Codes on Caterpillar ET Software

Diagnostic Capabilities

Diagnostic Codes
The engine’s Electronic Control Module (ECM) has the ability to monitor the circuitry between the ECM and the engine’s components. The ECM also has the ability to monitor the engine’s operating conditions. If the ECM detects a problem, a code is generated.

Diagnostic - Codes - on

There are three categories of codes:
-Diagnostic Code
-Event Code
-Flash Code

-Diagnostic Code – A diagnostic code indicates an electrical problem such as a short or an open in the engine’s wiring or in an electrical component.
-Event Code – An event code is generated by the detection of an abnormal engine operating condition. For example, an event code will be generated if the oil pressure is too low. In this case, the event code indicates the symptom of a problem. Event codes indicate mechanical problems rather than electrical problems.
-Flash Code – Diagnostics and events are reported via flash codes. When a diagnostic code or an event code becomes active, the specific condition is immediately reported to the operator through a series of flashes on the diagnostic lamp. By counting the flashes, a numeric representation of the diagnostic code or event code is revealed.

Codes can have two different states:
-Active
-Logged

-Active Codes
An active code indicates that a problem is present. Service the active code first. For the appropriate
troubleshooting procedure for a particular code, refer to the following troubleshooting procedure:
a. Troubleshooting, “Diagnostic Trouble Codes”
b. Troubleshooting, “Event Codes”
Refer to the Troubleshooting, “Diagnostic Code Cross Reference” for information that relates to converting flash codes to the equivalent diagnostic code or to the equivalent event code.

-Logged Codes
The codes are logged and stored in the CAT Electronic Technician. The problem may have been repaired and/or the problem may no longer exist. If the system is powered, it is possible to generate an active diagnostic code whenever a component is disconnected. If the component is reconnected, the code is no longer active but the code may become logged.
Logged codes may not indicate that a repair is needed. The problem may have been temporary. Logged codes may be useful to help troubleshoot intermittent problems. Logged codes can also be used to review the performance of the engine and of the electronic system.

May 18, 2019 Heavy Duty Diagnostic, , , , , , , , , , , , , , , , , , , , 0 Read more >

SIS Cat 2018 Caterpillar SIS Cat Caterpillar Software Free Download

SIS Cat 2018 is CAT Caterpillar ET 3 Diagnostic Adapter latest Caterpillar SIS .Cat SIS 2018 software including electronic catalog. contains spare parts catalogs, information on repairs, ect. Many clients asked the latest cat sis 2018 software .Therefore CnAutotool.com share SIS Cat 2018 Caterpillar SIS Cat Caterpillar torrent file software free download on mega.
SIS - Cat - 2018 - Caterpillar - SIS - Software -1 SIS - Cat - 2018 - Caterpillar - SIS - Software -2
SIS Cat 2018 Caterpillar SIS Overview

Year / Release Date: 2018
Version: 01.2018
Developer: Caterpillar Inc.
Operating system: Windows Vista / 7/8/10
Language: Multilingual
Description: Caterpillar Inc. electronic catalog. contains spare parts catalogs, information on repairs, maintenance and much more

SIS Cat 2018 Caterpillar SIS Software Free Download

Note:

SIS Cat 2018 software download resource is from internet,pls take your OWN RISK !!!

Meanwhile For worked and tested 100% Pls click

SIS Cat 2018

SIS Cat 2018 Caterpillar SIS Software Installation Instructions

Firstly Download the software

Secondly: Install software as following guide

1.Mount the image “Image.iso”. Then Run the file “Setup.exe”. Then Follow the prompts of the installer and install the electronic catalog.

2.Mount the “RERD0010.iso” image from the “Updates” folder. Then Run the file “Setup.exe”. Follow the prompts of the installer, install the updates. Then Repeat the same steps with the images “RERD0011.iso”, “RERD0012.iso”.

3. Then Install the programs from the “Tools” folder.

4. Unzip the archive “Crack.7z” from the folder “Crack”. Then Create the license file “license.dat”. To do this, run the file “Keygen.exe”, clear the “Host ID” field and enter the MAC address of the network card without spaces,Then click on the “Generate” button.

5. Create the folder “C: \ Caterpillar”,

6. Run the file “Environment.reg” from the folder “Crack”, agree to make changes to the registry. Then Restart the PC.

7. Start the electronic catalog. Then import the “User Authorization.xml” account from the “C: \ Caterpillar \ User Authorization” folder. And the login and password for the account are stored in the file “C: \ Caterpillar \ User Authorization \ User Authorization.txt”.

You can enjoy software finally.

May 15, 2019 Heavy Duty Diagnostic, , , , , , , , , , , , , , , , , , , , , , 0 Read more >

How can I get cat et license key and get cat et software downlaod via Internet

As we all know the cat et last version is 20014C v1.0，but the hardware only can use CAT ET Software,the question is the license is outdate,how can I get the last key?
Now I share the pic of getting the license key,
The fist is we need the software of cat et 2009Bv1.0,if you doesn’t have it, you can get it from me, I have the software 2009-2014c,all of them.

How-can-I-get-cat-et-license-key-1

Next and then you will see:

How-can-I-get-cat-et-license-key-2

And we accept the terms in the license agreement

How-can-I-get-cat-et-license-key-3

It is working, installing, When the software installation is complete, we will find the software icon on the desktop.

How-can-I-get-cat-et-license-key-4

Open it,

How-can-I-get-cat-et-license-key-5

Click ok tag, We see the Tips that the software without authorization.
Copy the license code,and sent it to me we can help you for license key.

How-can-I-get-cat-et-license-key-6

When paste the license key and authorize ,the cat et tell us it is licensed.

in fact,the steps of cat et 2010-2011B is the same as 2009B

April 5, 2019 Heavy Duty Diagnostic, , , , , , , , , , , , , , , , , , , , 0 Read more >

CAT Caterpillar ET Diagnostic Adapter has a powerful function

As a excellent Professional Diagnostic Tools products, CAT Caterpillar ET Diagnostic Adapter has a powerful function.it not only can Display “Logged Event Codes” to show engine over speeds,High temperatures, fuel consumption but also can view ECM’s current configuration and change user settings,perform diagnostic tests and calibrations, and calibrate.Electro-mechanical and electro-hydraulic components .

This is the only recommended communication device for CAT, and the only datalink device that will allow you to properly communicate with a CAT engine on dual datalinks. Context sensitive help leads operator through every task Cat ET can perform. Data Logger and Data Log Viewer allows recording of ECM signals for delayed troubleshooting capability.Cat “ET Trainer” is now included in ET Program. It allows Users to train and practice using Cat ET without a Communications adapter or Electronic Control Module (ECM).This is a free feature of Cat ET.

It is the latest generation of the CAT Communication Adapter group, and replaces the Caterpillar Tools This is the only recommended communication device for CAT, and the only datalink device that will allow you to properly communicate with a CAT engine on dual datalinks. This function is needed for some CAT ET (Electronic Technician) functions. The PC-based service tools from Caterpillar provide the capability to access Electronic Control Modules (ECMs) from a personal computer. Many job-critical tasks can be performed with an electronic service tool.

The user can display the status of a group of parameters (temperatures, pressures, etc.) simultaneously, view active and clear logged diagnostics, display the current configuration of an ECM and much more. The service tool works with a communication adapter to allow connection to an ECM. The version and identification of the ECM is automatically retrieved and is displayed on a summary screen when the program is started. Diagnostic tests and calibrations can also be performed.

More similar products can be found on www.cnautotool.com and any problem please feel free contact us.

February 19, 2019 Heavy Duty Diagnostic, , , , , , , , , , , , , , , , , , , , 0 Read more >

Caterpillar SIS 2018 CAT SIS 2018

There are 2 options for you to choose before order please:
1. Software is in a 320G hdd before shipment, the customers need to install it and active it in the laptop by themselves after receive the hdd.
2. Software would be installed well in a second hand dell d630 laptop before shipment, you could use it directly after you receive the dell D630 Laptop.
Languages: English, Spanish, Italian, Chinese, Mexican, German, French
OS: VISTA, Win7 x32, Win7 x64, Windows 8 x32, WinNT, WinXP
Date of update: 1/2018
The Caterpillar SIS 2018 (3D pictures) complete set contains the full information on spare parts, repair, electric circuits and etc. SIS has been tested using Microsoft Internet Explorer 5.5/6.0 on these platforms: Windows 2000 & Windows XP, VISTA and Windows 7.
SIS is the electronic service tool that Caterpillar dealers, customers and employees rely on for their parts and service information needs. SIS provides information for all Caterpillar machines and engines from 1977. SIS is available on the Internet, DVDs and a network version based on the DVD standalone application.
CAT SIS Web is updated continually and is the most complete and up to date version of SIS. SIS DVD and Network SIS use the same information that is located on the monthly data DVD’S. The time required to stage and ship the DVD’S to Dealer’s and Customer’s accounts for the delay in information that may be available from SIS DVD/Network.
SIS DVD is the standalone version of SIS and is required when the Caterpillar Inc. server for either SIS Web or the Dealer server for Network SIS is not available. Field Mechanics may be the largest group that uses SIS DVD. All three versions of SIS require an Internet Browser to display SIS information.
Caterpillar STW
The Service Technician Workbench is an integrated package of software tools, designed to assist the Caterpillar Service Technician during the machine repair process.
STW provides common installation of the following service software applications: STW Toolbar (STW Lauchpad), Service Information System (SIS),  Cat Electronic Technician(Cat ET), CBT Component Based Troubleshooting (CBT), Technical Analisis I (TA1) & Technical Analisis II (TA2), and Service Report.
STW Features:
Allows user to send data from SIS, TA and Heavy Duty Diagnostic Cat ET to an Electronic Service Report. All information about the repair is in one location.
Allows user to attach Cat ET Warranty Reports to the STW service report.
Allows user to attach digital photos to further document the repair.
A single source of support ? DDS Support Center
Electronic service reports are easier to archive than paper service reports.
Integration between Component Based Troubleshooting (CBT), Service Information System (SIS), Cat Electronic Technician (Cat ET), Flash File Search and Service Report.
The DBS Upload utility increases dealer efficiency by eliminating the need for the technician to re-type data into the service report, already created in DBS. This information is sent from DBS to STW to create a STW service report.
STW Lauchpad
The STW Launchpad allows to you: Conveniently launch Service Software Applications, Manage some common SIS/CBT preferences.
Families/Models/Prefixes
BROOM-ANGLE, SAHL BROOM, BCG
GENERATOR SET, 3516B, EDG
INDUSTRIAL ENGINE, C7.1, G9R
GENERATOR SET, C6.6, LC6
EXCAVATOR, 336F LH, LTP
MOTOR GRADER, 12M 3, N9F
MOTOR GRADER, 160M 3, N9L
ARTICULATED TRUCK, 725C, TFB
WHEEL TRACTOR-SCRAPER, 621K, WTL
ENGINE – MACHINE, C9.3, WYE
EXCAVATOR, M315D 2, CH3
GENERATOR SET, 3516B, JCY
HAMMER, B30, MAY
MOTOR GRADER, 140M 3, N9M
MOTOR GRADER, 12M 3 AWD, N9P
MOTOR GRADER, 12M 3, N9R
ENGINE – MACHINE, C9, SYE
PACKAGE, 3.4B IOPU, CJ3
BROOM-ANGLE, SAHL BROOM, H1W
GENERATOR SET, 3516C, JDH
EXCAVATOR, 336F LH, KGH
MARINE ENGINE, C140-16, P3P
ENGINE – MACHINE, C9, SSE
EJECTOR TRUCK, 730C, TFH
ARTICULATED TRUCK, 725C, LFB
MINI HYD EXCAVATOR, 300.9D, LJ2
MOTOR GRADER, 140M 3 AWD, N9J
EXCAVATOR, 336F H, NAJ
EXCAVATOR, 320E, SHX
WHEEL TRACTOR-SCRAPER, 627K LRC, WTN
BROOM-ANGLE, SAHL BROOM, BAW
EXCAVATOR, M317D 2, CH5
EXCAVATOR, 336E H, HDW
ARTICULATED TRUCK, 730C, LFF
EJECTOR TRUCK, 730C, LFH
MINI HYD EXCAVATOR, 301.7D, LJ4
MINI HYD EXCAVATOR, 302.7D, LJ7
MOTOR GRADER, 160M 3, N9E
ENGINE – MACHINE, C9.3, SYE
ARTICULATED TRUCK, 730C, TFF
WHEEL TRACTOR-SCRAPER, 627K, WTC
EXCAVATOR, 336E LH, JEA
MINI HYD EXCAVATOR, 302.4D, LJ6
MOTOR GRADER, 160M 3 AWD, N9T
ENGINE – MACHINE, C13, T4F
TRACK-TYPE TRACTOR, D6R, WBC
GENERATOR SET, 3516, JCW
MINI HYD EXCAVATOR, 301.4C, LJ3
MINI HYD EXCAVATOR, 302.2D, LJ5
MOTOR GRADER, 12M 3 AWD, N9B
MOTOR GRADER, 140M 3 AWD, N9G
MOTOR GRADER, 160M 3 AWD, N9K
WHEEL TRACTOR-SCRAPER, 621K, WTA
WHEEL TRACTOR-SCRAPER, 623K LRC, WTM
GENERATOR SET, 3516B, JDE
GENERATOR SET, 3516C, JDJ
EXCAVATOR, 336F LNH, MTW
MOTOR GRADER, 140M 3, N9D
EXCAVATOR, 336F LH, PFL
TRACK-TYPE TRACTOR, D6N OEM, SC6
ENGINE – MACHINE, C9.3, SSE
WHEEL TRACTOR-SCRAPER, 623K, WTB

STW Service Report
The STW Service Report is a tool to help you collect, report, and organize your service jobs.
– Allows for complete documentation of your repair.
– Reduce duplicate typing of Service Reports
– Easy to read
– Spell check
Easy integration with Dealer Business System (both DBS and DBSi):
Download header information from DBS
Upload service information to DBS after your job is completed
Collect information from other service tools, including:
Parts lists from SIS
ECM summaries and reports from Cat ET
Inspection lists from Technical Analysis (TA)

Component Based Troubleshooting
Component Based Troubleshooting (CBT) helps the technician troubleshoot symptoms and codes for Caterpillar engines and machines. After identifying a symptom, the technician is presented with a list of components that, if not operating properly, may cause the symptom. By using the information provided for each component, the technician can identify the root cause of the symptom and fix the problem. The technician is also presented with a list of available ECMs and codes for the selected model to troubleshoot diagnostic codes. In addition, Heavy Duty Truck Scanner gives the technician links to related information for symptoms and codes in the Service Information System (SIS).

Total: (Caterpillar SIS 2018 )
Caterpillar Disc #1: EXCAVATORS, OEM PRODUCTS
Caterpillar Disc #2: ELECTRIC POWER GENERATION
Caterpillar Disc #3: MARINE ENGINES, PETROLEUM PRODUCTS, TRUCK ENGINES
Caterpillar Disc #4: INDUSTRIAL ENGINES
Caterpillar Disc #5: EXCAVATORS, OEM PRODUCTS
Caterpillar Disc #6: PIPELAYERS, TRACK TYPE TRACTORS
Caterpillar Disc #7: INTEGRATED TOOLCARRIERS, WHEEL TYPE LOADERS, WHEEL TRACTOR SCRAPERS
Caterpillar Disc #8: WHEEL TYPE LOADERS
Caterpillar Disc #9: ARTICULATED DUMP TRUCKS, LOAD HAUL DUMP, MACHINE CONTROL GUIDANCE PRODUCTS, OFF HIGHWAY TRUCKS, UNDERGROUND ARTICULATED TRUCKS, ON HIGHWAY TRUCKS
Caterpillar Disc #10: BACKHOE LOADERS, CHALLENGERS, COMBINES, MINI EXCAVATORS, SKID STEER LOADERS, TILLAGE, TELSCOPIC MATERIAL HANDLERS, WORK TOOLS
Caterpillar Disc #11: ASPHALT PAVERS, COLD PLANERS, COMPACTORS, MOTOR GRADERS, ROAD RECLAIMERS
Caterpillar Disc #12: EXCAVATORS
Caterpillar Disc #13: TRACK TYPE TRACTORS
Caterpillar Disc #14: EXCAVATORS, OEM PRODUCTS
Caterpillar Disc #15: EXCAVATORS, OEM PRODUCTS
Caterpillar Disc #16: EXCAVATORS, OEM PRODUCTS
Caterpillar Disc #17: EXCAVATORS, OEM PRODUCTS
Caterpillar Disc #18: EXCAVATORS, OEM PRODUCTS
Caterpillar Disc #19: EXCAVATORS, OEM PRODUCTS

February 14, 2019 Heavy Duty Diagnostic, , , , , , , , , , , , , , , , , , , , , , , 0 Read more >

2018 Caterpillar SIS installation instrcution

You can install cat sis software following next steps.

1.Unzip iso,find SIS file,install setup.exe
2.Load iszwith virtual drive (Alcohol 120%),and install
3.Load isz,and install
4.Load isz,and install
5.Unzip sis_patch 123file,password is 123,Copy and paste the unzipped files to the SIS installation catalog.(Find SIS on desktop,click right key-file location)
6.Double click SIS icon,prompt to activate.
7.Unzip sis_kg 2013calculator,activate it.
8.Open SIS after activation,first it need load license,put yogocat masterin the desktop,find import user on SIS page.Then load.Choose the file yogocat master ,click √,click import,after jumping interface,click login.
9.Put ID and password to log in.ID:yogocatPASSWORD:master,next page choose cat dealer,agree with it,then you can open SIS homepage.

January 21, 2019 Heavy Duty Diagnostic, , , , , , , , , , , 0 Read more >

How to Update the Communication Adapter II Firmware to SIP

NOTE: Use the Auto Diagnostic tool Comm Adapter II Toolkit version 1.1, 1.93 or greater drivers to update the Comm Adapter II.

NOTE: Only use the serial port to upgrade the Comm Adapter II, do not use the Parallel port.

Instructions

To update the CAT ET Firmware, perform the following steps:

Step 1 Make sure the Comm Adapter II is connected to the PC and powered light is on.

Step 2 Go to the Start menu on your computer. Choose Programs -> Caterpillar Comm Adapter II -> Comm Adapter II Toolkit.

Step 3 The Toolkit application will start up and display the Summary screen.

Step 4 Choose the Application Firmware Flash icon (middle icon). The Select Firmware Flash File dialog box displays.

Step 5 You should see these files listed on the left:
ca2v1i0.apf – v1.0 application firmware
ca2v1i1.apf – v1.1 application firmware
ca2v1i1b1.apf – v1.1-B1 application firmware
ca2v2i2.apf – v2.2 application firmware
ca2v2i2_26.apf – SIP application firmware
Note: Caterpillar Communication Adapter (7X1701) does not support J1939 data link.

Step 6 Highlight the ca2v2i2_26.apf file and press the OK button.

Step 7 Press the Begin Flash button to start the download

Step 8 A dialog box showing the download progress will appear. The download should take less than 1 minute.

Step 9 The protocol lights on the front of the Comm Heavy Duty Diagnostic tool Adapter II will all flash while flashing the firmware.

Step 10 When the download is complete, a dialog box will appear allowing you to return to the Summary screen, the Flash screen, or Exit.

Step 11 Press the Exit button. For further details on the Toolkit application and the Application
Firmware Flash process, please refer to the Communication Adapter II User’s Manual.

June 26, 2018 Heavy Duty Diagnostic, , , , , , , , , , , , , , , , , , , , , , , 0 Read more >

Excel Export of Order Details Tab Data of CAT ET

All Order Details data can be exported in one step to an Excel spreadsheet file

The data of CAT ET from each Order Details tab will be populated on a separate worksheet in one Excel spreadsheet file

Click on the Export Excel button on the Order Details page to export the Order Details data

Excel Export of Order Details Tab Data

14-1 14-2

Order Details –Revoked Licenses Tab Detail

14-3

Order Details – Editable Fields

-> Order Name
-> Purchase Order
-> Organization
-> Attention – Only editable if license is Assigned

Order Details Editable by Dealer Admin
14-4

Order Details Editable by Auto Scanner

14-5

Order Details Attention
* – Editable by Dealer Admin
* License must be Assigned

14-6
14-7
14-8

January 30, 2018 Auto Scanner Tools, , , , , , , , , , , , , , , , , , , , , , , 0 Read more >

Licensing Expiration Schedule

Cat ET
–Dealer Cat ET license will run January – December each year
–Customer CAT ET license expires 365 days from the date the license ORDER is placed in the Dealer Software Licensing (DSL) system

SIS DVD and SIS Network
–Dealer  SIS DVD license will run January – December each year
–Customer SIS DVD license expires 365 days from the date the license ORDER is Placed in the Dealer Software Licensing (DSL) system

9-1 9-2

Managing Licenses
– Yearly Orders of Licenses
– Caterpillar created License Orders for each Dealer by Subscription Type for Dealer
– Caterpillar Renews DEALER SITE LICENSE Orders (JERD2129, RERA0004 & NEXG5043) in October and will renew yearly
– Each Dealer will need to Renew their CUSTOMER Orders by Subscription Type for Customer Usage (JERD2125, NEXG5007, NEXG5009, RERA0003, etc.) prior to the Order Expiration Dates

Managing Licenses
– Assigning a License
– Each order contains a specific number of licenses
– A license is UNASSIGNED until an authorized DSL user ASSIGNS the license by NAME to an individual user

9-3

9-4

New Software License Order

Yearly Order of the Number of Licenses Required
Customer Subscriptions automotive scan tool Cat ET and SIS DVD
Dealer Subscriptions Olympian EST Olympian Compass USB

New Software License Order ET Caterpillar

9-5

New Software License Order – Cat ET Customer

9-6
New Software License Order – Cat ET Customer

9-7 9-8

New Software License Order Receipt

9-9

Assign a License

9-10

9-11

January 29, 2018 Auto Scanner Tools, Car Diagnostic Tools, , , , , , , , , , , , , , , , , , , , , , , 0 Read more >

Transferring a License of CAT ET

Transferring a License of  CAT ET
29-1

Important
If you are transferring your service tool license from another computer, you must have the Serial Number from the original license.

Instructions

To transfer your license, complete these two steps:

Step 1
Obtain the Serial Number from the original service tool program. If you do not know this number, select About Electronic Technician from the Help menu. The Serial Number will display in the message box. Write down the Serial Number.

Step 2
Install the Best Car Diagnostic Tool onto the new computer (the computer you are transferring your license to). With the Licensing dialog box displayed in front of you, call Caterpillar Media and Product Information Logistics. Refer to “Licensing Caterpillar Electronic Technician,”

January 27, 2018 Auto Scanner Tools, , , , , , , , , , , , , , , , , , , , , , , 0 Read more >